Motorola SYMBOL LS7708 Especificaciones Pagina 111
- Pagina / 380
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
RS-232 Host Interface 6-5
Figure 6-2. RS-232 Connection with Peripherals - Power Supplied Externally
1. Connect the RS-232 interface cable to the host port of the scanner.
2. Connect the other end of the interface cable to the serial port on the host.
3. Connect the peripherals, if any, to their respective ports (see Figure 6-2).
4. Connect the power supply.
5. Scan appropriate bar codes in this chapter or use 123Scan to match the host settings.
Interface cables vary depending on configuration. The connectors may be different from the examples
illustrated, but the steps to connect the scanner are the same. See Chapter 1, Getting Started for connection
information.
Host Port
Power Port
Power Supply
RS-232 Auxiliary Device
Hand-Held Scanner
To EAS
(optional)
Host Serial Port
- Symbol LS7708 1
- Product Reference Guide 3
- Revision History 5
- Contents 7
- Chapter 4. User Preferences 8
- Chapter 7. USB Interface 9
- Chapter 9. Synapse Interface 10
- Chapter 12. 123Scan 10
- Chapter 13. Symbologies 11
- Appendix C. Sample Bar Codes 12
- Appendix D. Numeric Bar Codes 13
- Appendix E. Mounting Template 13
- Glossary 13
- Tell Us What You Think 13
- About This Guide 15
- Chapter Descriptions 17
- Notational Conventions 18
- Related Publications 18
- Service Information 18
- Getting Started 19
- Unpacking the Scanner 22
- Input/Output Ports 23
- Setting Up the Scanner 24
- Routing Cables 26
- Configuring the Scanner 27
- Synchronization of Settings 27
- Freestanding Configuration 28
- Attached Configuration 29
- To detach the scanner: 31
- Scanning 33
- Active Scan Area 35
- Scanning Bar Codes 35
- Beeper Definitions 37
- Selecting Beeper Volume 38
- Sleep Mode 38
- LED Definitions 38
- Decode Zone 39
- Considerations 40
- Maintenance and 41
- Technical Specifications 41
- Maintenance 43
- Replacing the Scanner Window 44
- Troubleshooting 46
- Scanner Signal Descriptions 49
- SYNDATA SYNCLK VCC GND - 51
- Pin 1Pin 2Pin 3Pin 4 51
- VCC GND - INTERLOCK 51
- User Preferences 53
- Beeper Tone (continued) 58
- Beeper Volume 59
- High Beeper Volume 60
- *Beep After Good Decode 61
- Low Power Mode 62
- *Low Power Blink Mode 62
- Scan Pattern Mode 63
- Timeout Between Decodes 64
- Time Delay to Low Power Mode 65
- 60 Minutes 66
- 90 Minutes 66
- Linear UPC/EAN Decode 67
- UPC Half Block Stitching 68
- EAS Interlock 69
- Keyboard Wedge Interface 71
- Keyboard Wedge Host Types 77
- IBM AT NOTEBOOK 78
- NCR 7052 78
- *North American 79
- French Windows 80
- French Canadian Win 95/98 80
- Keyboard Wedge Interface 5-11 81
- Spanish Windows 81
- Italian Windows 82
- Swedish Windows 82
- Keyboard Wedge Interface 5-13 83
- UK English Windows 83
- Japanese Windows 83
- Keystroke Delay 85
- *No Delay 85
- Keystroke Delay (continued) 86
- Intra-Keystroke Delay 87
- Caps Lock On 89
- *Disable Caps Lock On 89
- Caps Lock Override 90
- *Disable Caps Lock Override 90
- Convert Wedge Data 91
- No Convert 92
- FN1 Substitution 94
- Send Make Break 95
- OnKeyboard Maps 96
- OnKeyboard Maps (continued) 97
- RS-232 Host Interface 107
- Introduction 109
- Host Port 110
- Host Serial Port 110
- To EAS (optional) 110
- RS-232 Default Parameters 112
- RS-232 Host Interface 6-7 113
- RS-232 Host Types 115
- RS-232 Host Types (continued) 116
- Baud Rate 119
- Baud Rate (continued) 120
- RS-232 Host Interface 6-17 123
- Parity (continued) 124
- Check Receive Errors 126
- *Check For Received Errors 126
- Hardware Handshaking 127
- Standard RTS/CTS 128
- RTS/CTS Option 1 128
- RTS/CTS Option 2 129
- RTS/CTS Option 3 129
- Software Handshaking 130
- ACK/NAK with ENQ 131
- Host Serial Response Time-out 132
- *Minimum: 2 Sec 132
- RS-232 Host Interface 6-27 133
- Low: 2.5 Sec 133
- Medium: 5 Sec 133
- High: 7.5 Sec 134
- Maximum: 9.9 Sec 134
- RTS Line State 135
- *Host: Low RTS 135
- Stop Bit Select 136
- *1 Stop Bit 136
- Data Bits 137
- Beep on <BEL> 138
- Intercharacter Delay 139
- *Minimum: 0 msec 139
- Medium: 50 msec 140
- High: 75 msec 140
- Nixdorf Beep/LED Options 141
- Beep/LED After Transmission 142
- Beep/LED After CTS Pulse 142
- Ignore Unknown Characters 143
- ASCII / Character Set 144
- USB Interface 149
- Connecting a USB Interface 151
- (optional) 152
- USB Default Parameters 154
- USB Host Parameters 155
- USB Device Type (continued) 156
- USB Interface 7-9 157
- French, Windows 157
- German, Windows 158
- French Canadian, Windows 158
- USB Interface 7-11 159
- Italian, Windows 160
- Swedish, Windows 160
- USB Interface 7-13 161
- UK English, Windows 161
- Japanese, Windows (ASCII) 161
- USB Keystroke Delay 162
- USB Interface 7-15 163
- Medium Delay (20 msec) 163
- Long Delay (40 msec) 163
- USB CAPS Lock Override 164
- USB Ignore Unknown Characters 165
- Emulate Keypad 166
- USB Keyboard FN1 Substitution 167
- Function Key Mapping 168
- Simulated Caps Lock 169
- Convert Case 170
- Convert Case (continued) 171
- ASCII Character Set 172
- IBM 468X/469X Interface 181
- IBM Default Parameters 185
- IBM 468X/469X Host Parameters 186
- Port Address (continued) 187
- Convert Unknown to Code 39 188
- Synapse Interface 189
- Synapse Interface 9-5 193
- Synapse adapter cable 193
- To scanner 193
- Synapse Smart Cable 193
- RS-232 Auxiliary Port 195
- Power Port 198
- RS-232 Aux Port 198
- *Baud Rate 9600 201
- RS-232 Auxiliary Port 10-9 203
- Serial Response Time-out 211
- RS-232 Auxiliary Port 10-19 213
- Hand-Held Laser Scanner Port 217
- Parameter Default Page Number 220
- Programming Mode 221
- Program All Scanners 222
- Beep After Good Decode 223
- 123Scan Parameter 227
- Symbologies 229
- Scanning Sequence Examples 231
- Errors While Scanning 231
- Symbology Default Parameters 231
- Enable/Disable UPC-A/UPC-E 235
- *Enable UPC-A 235
- Enable UPC-E 236
- Disable UPC-E 236
- Enable/Disable UPC-E1 237
- *Disable UPC-E1 237
- *Enable EAN-13/JAN-13 238
- Symbologies 13-11 239
- Enable EAN-8/JAN-8 239
- Disable EAN-8/JAN-8 239
- Enable/Disable Bookland EAN 240
- *Disable Bookland EAN 240
- Decode UPC/EAN Supplementals 241
- Symbologies 13-15 243
- Enable 977 Supplemental Mode 244
- Symbologies 13-17 245
- Enable 491 Supplemental Mode 245
- Symbologies 13-19 247
- Symbologies 13-21 249
- *Transmit UPC-A Check Digit 251
- Transmit UPC-E Check Digit 252
- Symbologies 13-25 253
- Transmit UPC-E1 Check Digit 253
- UPC-A Preamble 254
- *System Character 254
- UPC-A Preamble (continued) 255
- UPC-E Preamble 255
- UPC-E Preamble (continued) 256
- UPC-E1 Preamble 257
- UPC-E1 Preamble (continued) 258
- Convert UPC-E to UPC-A 259
- Convert UPC-E1 to UPC-A 260
- EAN Zero Extend 261
- *Disable EAN Zero Extend 261
- Bookland ISBN Format 262
- UCC Coupon Extended Code 263
- Code 128 264
- Enable/Disable UCC/EAN-128 265
- *Enable UCC/EAN-128 265
- Enable/Disable ISBT 128 266
- *Enable ISBT 128 266
- Code 128 Decode Performance 267
- Symbologies 13-41 269
- Enable/Disable Code 39 270
- *Enable Code 39 270
- *Disable Trioptic Code 39 271
- Convert Code 39 to Code 32 272
- Code 32 Prefix 273
- *Disable Code 32 Prefix 273
- Set Lengths for Code 39 274
- Symbologies 13-47 275
- Code 39 - Length Within Range 275
- Code 39 - Any Length 275
- *Disable Code 39 Check Digit 276
- Transmit Code 39 Check Digit 277
- *Disable Code 39 Full ASCII 278
- *Do Not Buffer Code 39 279
- Buffer Data 280
- Clear Transmission Buffer 280
- Transmit Buffer 281
- Code 39 Decode Performance 283
- Symbologies 13-57 285
- Enable/Disable Code 93 286
- *Disable Code 93 286
- Set Lengths for Code 93 287
- Code 93 - Length Within Range 288
- Code 93 - Any Length 288
- Enable/Disable Code 11 289
- *Disable Code 11 289
- Set Lengths for Code 11 290
- Symbologies 13-63 291
- Code 11 - Length Within Range 291
- Code 11 - Any Length 291
- *Disable 292
- One Check Digit 292
- Symbologies 13-65 293
- Two Check Digits 293
- Transmit Code 11 Check Digits 294
- Interleaved 2 of 5 (ITF) 295
- Symbologies 13-69 297
- I 2 of 5 - Any Length 297
- Symbologies 13-71 299
- OPCC Check Digit 299
- Transmit I 2 of 5 Check Digit 300
- Convert I 2 of 5 to EAN-13 301
- Discrete 2 of 5 (DTF) 302
- Symbologies 13-75 303
- Symbologies 13-77 305
- D 2 of 5 - Any Length 305
- Codabar (NW - 7) 306
- Set Lengths for Codabar 307
- Codabar - Length Within Range 308
- Symbologies 13-81 309
- Codabar - Any Length 309
- CLSI Editing 310
- *Disable CLSI Editing 310
- NOTIS Editing 311
- *Disable NOTIS Editing 311
- RSS (Reduced Space Symbology) 312
- RSS Limited 313
- *Disable RSS Limited 313
- RSS Expanded 314
- Convert RSS to UPC/EAN 315
- Redundancy Level 316
- *Redundancy Level 1 316
- Redundancy Level 2 317
- Redundancy Level 3 317
- Redundancy Level 4 318
- Security Level 319
- * Security Level 0 319
- Security Level (continued) 320
- Bi-directional Redundancy 321
- *Normal Intercharacter Gaps 322
- Miscellaneous Scanner Options 323
- Transmit Code ID Character 326
- Prefix/Suffix Values 327
- FN1 Substitution Values 328
- Scan Data Options 329
- *Data As Is 330
- <DATA> <SUFFIX> 330
- <PREFIX> <DATA> 331
- Data Format Cancel 332
- Report Version 333
- Report MIMIC Version 333
- Report Synapse Cable 334
- Standard Default Parameters 335
- Report MIMIC Version 14-11 341
- Report Synapse Cable 14-12 341
- Programming Reference 343
- Symbol Code Identifiers 345
- AIM Code Identifiers 346
- Sample Bar Codes 349
- UPC-A, 100 % 351
- EAN-13, 100 % 352
- Interleaved 2 of 5 353
- 12345678901231 353
- Numeric Bar Codes 355
- Mounting Template 363
- CAD Drawing at 418% 365
- Numerics 373
Relacionado con productos y manuales para Lectores De Códigos De Barras Motorola SYMBOL LS7708
(80 paginas)
(2 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.039 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales