Motorola DSR-4550 Manual de instrucciones

Document No.: 540038-001DSR-4550 CommercialIntegrated Receiver/Decoder Operator Guide

DSR-4550 1 1Introducing the DSR-4550The Motorola Mobility DSR-4550 is a commercial Integrated Receiver Decoder (IRD) designed for cable operators an

12 • Two video outputs. One for primary video and one for OSD video. Outputs either 525-line NTSC/PAL M or 625-line PAL video formats, automatically m

DSR-4550 3 Introducing the DSR-4550Disaster RecoveryThe DSR-4550 performs automatic disaster recovery of lost L-band signal without operator interve

14 GigE Gigabyte EthernetGND GroundH/LHP Horizontal/Left-Hand PolarizationISOC IsochronousIF Intermediate FrequencyIP Internet ProtocolIRD Integrated

DSR-4550 5 2Connecting the DSR-4550Unpacking and Connecting the DSR-4550Cable connections, described in this chapter, are made to the back panel of t

26 Figure 2-2: DSR-4550 Back Panel (Detailed)UnpackingThe shipping carton contains the DSR-4550, two quick disconnect terminals, a power cord, and th

DSR-4550 7 Connecting the DSR-4550Rack Mounting GuidelinesThe DSR-4550, with the supplied mounting brackets is designed for installation in an EIA s

28 Connecting a DSR-4550 for L-Band InputTo Connect a DSR-4550 for a New DigiCipher II Service1. Determine which satellite, transponder, Virtual Chann

DSR-4550 9 Connecting the DSR-4550these internally generated cue tones are used, connect the 600-ohm differential Cue Tone+ and Cue Tone- terminals

OPERATION PRECAUTIONSWARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE.The lightning flash with the arrowhead

DSR-4550 11 3Operating the DSR-4550All operations described in this chapter require use of the DSR-4550 front panel, as shown in Figure 3-1.Figure 3-1

312 Using the Front PanelThe front panel LCD screen displays a series of menus that can be used to configure and control the system. The name of the c

DSR-4550 13 Operating the DSR-4550Navigating the MenusEven though the keypad options shown on the LCD screen may change for each menu and for each f

314 How to Use the MenusAbout MenuThe front panel LCD displays the About menu when the DSR-4550 is initially plugged in or after a factory reset. This

DSR-4550 15 Operating the DSR-4550Overview of the LCD Panel Menu TreePressing the ENTER button when the cursor is on a menu name causes the cursor t

316 Channel Selection MenusE 00000 MPEG SELECT ProgramE 00000 0000 (Not in map) CHANNEL  VCT  Chnl Xpnd

DSR-4550 17 Operating the DSR-4550 E TransmittedVITS Waveform Diagnostic Menus E OffDIAGN

318 Installation MenusThe purpose of the installation menus is to configure the ports and choose settings that remain fixed over a period of time (i.e

DSR-4550 19 Operating the DSR-4550Input Field Default: Port 1Note: Unless changed, the DSR-4550 displays values for an L-band input on Port 1. The I

Important Safety Instructions• Read these instructions.• Keep these instructions.• Heed all warnings.• Follow all instructions.• Do not use this appar

320 Xpnr Field Default: 1Note: This field is not available when the ASI In option in the Input field is selected. The Xpnr field cannot be edited if L

DSR-4550 21 Operating the DSR-4550Modulation MenuNote: This menu is not available when the ASI In option is selected. That option is located in the

322 Symbol/Code/Format Field Default: Mode-DependantNote: This field is not available when the DCII-Auto option in the Mode field is selected.The symb

DSR-4550 23 Operating the DSR-4550ID Field Default: 1Use this field to choose which L-band port to configure. Press the 4 button until the cursor is

324 Port Config MenuUse this menu to configure the LNB converter power for port 1.Port Test FieldThis function is not supported at this time.Port1 Pow

DSR-4550 25 Operating the DSR-4550AudioMix Field Default: StereoThis field allows selection of the audio processing options. Press the 4 button unti

326 Audio1 Gain and Audio2 Gain MenusThese menus allow adjustment of the audio signal output level from 0 to -20dB in 1dB increments. Press the  but

DSR-4550 27 Operating the DSR-4550Subcarrier MenuThe Subcarrier menu is used to set up standard settings used for analog manual tuning. Press the 4

328 Trigger Field Default: AutoThe Trigger field allows the user to select the trigger condition to activate an alarm on the IRD. When the alarm is ac

DSR-4550 29 Operating the DSR-4550Test Field Default: OffNote: The Test field returns to the default value (Off) when the field is exited.The Test f

PRECAUCIONES DE OPERACIÓNADVERTENCIA: PARA EVITAR RIESGOS DE INCENDIOS O DESCARGA ELÉCTRICA, NO EXPONGA ESTE EQUIPO A LA LLUVIA O LA HUMEDAD.El símbol

330 Reset MenuThe Reset menu allows the user to reset the unit to the factory default settings or perform a power cycle. Press the  buttons until th

DSR-4550 31 Operating the DSR-4550Press any arrow button (4) to back out of the field and leave it unchanged. Otherwise, press the ENTER button t

332 Video Out Format MenuThe Video Out Format menu allows the user to configure the video format. Press the  buttons until the Video Out Format menu

DSR-4550 33 Operating the DSR-4550Aspect Ratio MenuThe Aspect Ration Menu displays the current input aspect ratio and has one field that allows the

334 Digital Video/Audio MenuThe Digital Video/Audio Menu configures the digital video/audio rear-panel connections (either enabled or disabled). Press

DSR-4550 35 Operating the DSR-4550Firmware MenuThe Firmware menu displays the DSR-4550's firmware release information, which is equivalent to t

336 File FieldThe File field consists of two subfields:• Subfield #1 is editable and selects, by index, a download file for monitoring. • Subfield #2

DSR-4550 37 Operating the DSR-4550Channel MenusTo access the Channel menus, press ENTER button to return to the main top-level menu (shown below). P

338 Chnl FieldThe Chnl (Channel) field allows selection of the virtual channel for the output service. Channels that exist in the Virtual Channel Map

DSR-4550 39 Operating the DSR-4550Note: The caution message shown on the previous page is only displayed when the user changes the channel from a va

Instrucciones de seguridad importantes• Lea estas instrucciones.• Guarde estas instrucciones.• Considere todas las instrucciones.• Siga todas las inst

340 MPEG Select MenuThis menu allows the user to select which service is displayed at the video and audio outputs by specifying the MPEG program numbe

DSR-4550 41 Operating the DSR-4550Aud1Lang, Aud2Lang MenusThese menus (Audio1 and Audio2 Language) have three fields that allow the user to modify a

342 Left and Right Fields Default: DefNote: These fields operate in conjunction with the "Audio1 and Audio2 Menus" on page 24 (specifically

DSR-4550 43 Operating the DSR-4550• If the AudioMix option (described on page 25) is set to Dual Mono and a language pair is not available that matc

344 EMM ID MenuThe Entitlement Management Message (EMM) ID menu allows for additional flexibility in access control. It allows the user to enter a new

DSR-4550 45 Operating the DSR-4550IP MenusUse the IP menus is to configure the 10/100 port. To access the IP menus, press ENTER button to return to

346 Subnet Mask MenuUse the following procedure to set and view the Subnet Mask IP address (range: 000.000.000.000 to 255.255.255.255) for the lower E

DSR-4550 47 Operating the DSR-4550GigE MenusUse the GigE menus is to configure the GigE port. To access the GigE menus, press ENTER button to return

348 GigE Subnet Mask MenuUse the following procedure to set and view the GigE Subnet address (range: 000.000.000.000 to 255.255.255.255) for the upper

DSR-4550 49 Operating the DSR-4550GigE MPTS Address MenuUse the following procedure to set and view the GigE Multiple Program Transport Stream (MPTS

350 Status Display MenusNote: Some of the status screens are not displayed when the active signal is received from a source other than the L-band inpu

DSR-4550 51 Operating the DSR-4550Status2 MenuNote: This menu is not displayed when the active signal is received from a source other than the L-ban

352 Status4 MenuNote: This menu is not displayed when the active signal is received from a source other than the L-band input connector.Press the  b

DSR-4550 53 Operating the DSR-4550Status5 MenuNote: This menu is not displayed when the active signal is received from a source other than the L-ban

354 Status6 MenuPress the  buttons until the Status6 menu appears (shown below). This screen displays the DSR-4550’s Memory (free memory) and Flash

DSR-4550 55 Operating the DSR-4550Diagnostics MenusThe DSR-4550's diagnostic menus allow the user to isolate problems to the DSR-4550 or the sa

356 Clear Cntrs FieldNote: If a diagnostic menu other than Off is selected, the Clear Cntrs (clear counters) field also appears. This field is primari

DSR-4550 57 Operating the DSR-4550Audio Test Signal MenuThis menu allows the user to select an audio test signal for each of the two audio outputs,

358 Video Test Signal MenuA full-field video test signal is available and the user can display different test patterns by selecting the Pattern field.

DSR-4550 59 Operating the DSR-4550VITS MenuThis menu allows the user to insert VITS on lines 17 or 18. Press the  buttons until the Vertical Inter

DSR-4550 iChapter 1 Introducing the DSR-4550 ...

360 Field Field Default: 1Note: The IRD does not display this field when the waveform is set to Transmitted or Disabled.The Field field allows the use

DSR-4550 61 Operating the DSR-4550Ad Insertion Test MenuThe Ad Insertion Test menu allows the user to turn cue tones and the relays on and off. Ad i

DSR-4550 63 4TroubleshootingBefore contacting the Hotline, review Table 4-1 for problems and suggested solutions.Table 4-1: Troubleshooting Solutions

DSR-4550 65 5Downlink/L-band FrequencyConversion TablesA distributor or programmer can provide the latest L-band frequency plans at purchase time. Use

DSR-4550 67 6Product SupportIf You Need HelpFor assistance with Motorola Mobility products, contact Motorola Technical Support,24 hours a day, 7 days

668 Calling for RepairsIf repair is necessary, call Motorola Mobility’s authorized repair vendor, World Wide Digital at 1-800-227-0450 or 1-956-541-06

DSR-4550 69 7Language AbbreviationsNote: This list of languages was recommended to system operators as the appropriate identifiers for audio, subtitle

TOCii Aspect Ratio Menu ... 33Inpu

770 Panjabi pan Portuguese porJapanese jpn Rajasthani rajJavanese jav Romanian rumKashmiri kas Russian rusKorean kor Samoan smoKurdish kur Scots scoLa

DSR-4550 71 8DiagnosticsIntroductionThe Fast Fact Diagnostic screens (1 through 5) are a part of the IRD firmware created during product development a

872 Viewing the Fast Fact Diagnostic ScreensThe diagnostic screens (Figure 8-1) are available via the On-Screen Display (OSD) video out using a video

DSR-4550 73 DiagnosticsFast Facts ScreensThe Fast Facts screens are used as a method of viewing information and diagnostic data associated with the

874 VCT ID Shows the current VCT ID.Encryption Displays the current program’s encryption status.Service Displays the service number for the current pr

DSR-4550 75 DiagnosticsFast Facts 2The Fast Facts 2 screen displays information relating to the port configuration of the IRD.Field Name DefinitionP

876 Fast Facts 3The Fast Facts 3 screen displays information relating to video information.Field Name DefinitionVideo Locked An indication of video lo

DSR-4550 77 DiagnosticsResolution Displays the Horizontal Size X Vertical Size of the received video.Film Mode Indication of if Film Mode is active

878 Fast Facts 4The Fast Facts 4 screen displays information relating to audio information. There are two columns of information displayed, one column

DSR-4550 79 DiagnosticsFast Facts 5 (10/100 Network)The Fast Facts 5 screen displays information relating to the Ethernet configuration.Field Name D

DSR-4550 iiiStatus4 Menu ...

880 Fast Facts 5 (Gigabit Ethernet)The Fast Facts 5 (Gigabit Ethernet) screen displays information relating to Gigabit Ethernet configuration.Field Na

DSR-4550 81 9DSR-4550 Specifications RFInput Frequency Range 950 to 2150 MHzInput RF Level -25 to -65 dBmRF Port Impedance 75 OhmsRF Port Return Loss

982 Note: Audio and data connectors may be ordered through Phoenix Contact part numbers 1840447 / 1840528.Video (SDI)Format SMPTE-259M Standard with

DSR-4550 83 DSR-4550 SpecificationsAudio (Digital)Format AES (discrete), AES3, SMPTE-272, and SMPTE-291M (embedded)Outputs Right Channel, Left Chann

984 Note: Audio and data connectors may be ordered through Phoenix Contact part numbers 1840447 / 1840528. OSD Video Out BNC (Qty 1)GigE (Ethernet) RJ

Caring for the Environment by Recycling When you see this symbol on a Motorola pdo not dispose of the product with residentiacommercial waste. roduct,

6450 Sequence Dr.San Diego, CA 92121Document No: 540038-001, Rev. F540038- 001- 99PLEASE RECYCLE