Motorola AP-51XX Manual de usuario Pagina 205
- Pagina / 698
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Network Management
5-57
3. Configure the Radio Settings field to assign a channel, antenna diversity setting, radio
transmit power level and data rate.
Radio Type The Radio Type parameter simply displays the radio type as
802.11a or 802.11b/g. This field is read only and always displays
the radio type selected from the access point menu tree under the
Radio Configuration item.
ERP Protection Extended Rate PHY (ERP) allows 802.11g MUs to interoperate with
802.11b only MUs. ERP Protection is managed automatically by the
access point and informs users when 802.11b MUs are present
within the access point’s coverage area. The presence of 802.11b
MUs within the 802.11g coverage area negatively impacts network
performance, so this feature should looked to as an indicator of
why network performance has been degraded.
Channel Setting The following channel setting options exist:
User Selection - If selected, use the drop-down menu to specify
the legal channel for the intended country of operation. The drop-
down menu is not available if this option is not selected.
Automatic Selection - When the access point is booted, the
access point scans non-overlapping channels listening for beacons
from other access points. For 802.11b, it scans channels 1, 6, and
11. For 802.11a, all channels are non-overlapping. After the
channels are scanned, it will select the channel with the fewest
access points. In the case of multiple access points on the same
channel, it will select the channel with the lowest average power
level.
The Uniform Spreading option is available (and is the default
setting for the 802.11a radio). To comply with Dynamic Frequency
Selection (DFS) requirements in the European Union, the 802.11a
radio uses a randomly selected channel each time the access point
is powered on.
Antenna Diversity Specifies the antenna selection for the 802.11a radio. Options
include Primary Only, Secondary Only and Full Diversity. The default
setting is Primary. However, Diversity can improve performance
and signal reception in areas where interference is significant and
is recommended when two antennas are supported.
Power Level Defines the transmit power of the 802.11a or 802.11b/g antenna(s).
The values are expressed in dBm and mW.
- Product Reference Guide 1
- AP-51xx Access Point 3
- Product Reference Guide 3
- Contents 5
- Chapter 3. Getting Started 8
- Chapter 5. Network Management 9
- Chapter 8. CLI Reference 11
- Chapter 10. Adaptive AP 13
- Appendix B. Usage Scenarios 14
- Appendix C. Customer Support 14
- About This Guide 15
- Notational Conventions 16
- Service Information 16
- Introduction 17
- 1.1 New Features 18
- 1.1.2 Rogue AP Enhancements 19
- 1.1.5 QBSS Support 19
- 1.2 Feature Overview 20
- 1.2.8.2 EAP Authentication 25
- 1.2.8.3 WEP Encryption 25
- 1.2.8.4 KeyGuard Encryption 26
- 1.2.8.7 Firewall Security 27
- 1.2.8.8 VPN Tunnels 27
- 1.2.8.9 Content Filtering 27
- 1.2.9 VLAN Support 28
- 1.2.11 Updatable Firmware 28
- 1.2.15 Voice Prioritization 30
- 1.2.17 Statistical Displays 31
- 1.2.18 Transmit Power Control 31
- 1.2.22 DHCP Support 32
- 1.2.23 Multi-Function LEDs 33
- 1.2.24 Mesh Networking 33
- 1.2.25 Additional LAN Subnet 34
- 1.2.27 Hotspot Support 35
- 1.3 Theory of Operations 36
- 1.3.1 Cellular Coverage 37
- 1.3.2 MAC Layer Bridging 38
- 1.3.3 Media Types 38
- 1.3.5 MU Association Process 39
- 1.3.6 Operating Modes 40
- Hardware Installation 45
- 2.1 Precautions 46
- Part No. Description 47
- 2.2.2 AP-5181 Configurations 48
- 2.3 Requirements 49
- 2.4 Access Point Placement 49
- 2.4.1 Site Surveys 50
- 2.4.2 Antenna Options 50
- 2.5 Power Options 53
- 2.5.2 AP-5181 Power Options 54
- 2.7 Mounting an AP-5131 57
- Light Pipe 65
- Ceiling Tile 65
- 2.8 AP-5131 LED Indicators 67
- 2.9 Mounting an AP-5181 68
- Attach the square 69
- 2.10 AP-5181 LED Indicators 73
- Data over Ethernet 74
- 802.11a radio activity 74
- 802.11b/g radio activity 74
- 2.11 Setting Up MUs 75
- Getting Started 77
- 3.2 Configuration Options 78
- 3.5.2 Testing Connectivity 90
- 3.5.3 Where to Go from Here? 91
- 4.2 Adaptive AP Setup 98
- 4.3 Configuring Data Access 101
- System Configuration 103
- 4.5 Configuring SNMP Settings 115
- Feature MIB Feature MIB 116
- SNMP v3 user definitions 119
- SNMP access 122
- 4.5.2 Enabling SNMP Traps 123
- 4.7 Logging Configuration 134
- 4.9 Updating Device Firmware 141
- Network Management 149
- 5.2 Configuring WAN Settings 164
- WAN port 167
- 5.2.2 Configuring Dynamic DNS 173
- has data traffic to forward 212
- 6.2 Setting Passwords 221
- New Security Policy screen 224
- 3. Refer to the 246
- 6.10.1.1 Available Protocols 251
- 6.11 Configuring VPN Tunnels 254
- Key Settings screen 264
- 6.11.4 Viewing VPN Status 268
- Details button 278
- 4. Refer to the 279
- Delete-> button 293
- Monitoring Statistics 299
- 7.1 Viewing WAN Statistics 300
- 7.2 Viewing LAN Statistics 304
- 7.3.1 Viewing WLAN Statistics 313
- 7.4.1.1 Retry Histogram 322
- 7.5.1 Viewing MU Details 325
- 7.5.2 Pinging Individual MUs 328
- CLI Reference 335
- 8.1 Connecting to the CLI 336
- 8.2 Admin and Common Commands 337
- AP51xx>admin>help 338
- AP51xx>admin>passwd 339
- AP51xx>admin>summary 340
- AP51xx>admin> 341
- AP51xx>admin> / 342
- AP51xx>admin>save 343
- AP51xx>admin>quit 344
- 8.3 Network Commands 345
- 8.3.1 Network LAN Commands 346
- Description: 347
- Syntax: 347
- Example: 347
- Related Commands: 350
- 8.3.2 Network WAN Commands 374
- 8.3.3.1 Network WLAN Commands 401
- 8.3.3.3 Network ACL Commands 422
- Descripton: 447
- 8.3.5 Network Router Commands 470
- 8.4 System Commands 476
- 8.4.2 System Access Commands 486
- Description: ) 491
- 8.4.4 System SNMP Commands 502
- 8.4.6 System Radius Commands 527
- Description: set 536
- 8.4.8 System Log Commands 555
- 8.5 Statistics Commands 572
- Configuring Mesh Networking 589
- 9.1.5 Normal Operation 594
- 9.3.1.1 Configuring AP#1: 609
- 9.3.1.2 Configuring AP#2 614
- 9.3.1.3 Configuring AP#3 615
- Repeater and a Client Bridge 619
- 9.3.2.1 Configuring AP#1 620
- 9.3.2.2 Configuring AP#2 620
- 9.3.2.3 Configuring AP#3 621
- Adaptive AP 629
- 10.1.1 Where to Go From Here 630
- 10.1.2 Adaptive AP Management 631
- 10.1.3 Types of Adaptive APs 631
- 10.1.4 Licensing 632
- 10.1.5 Switch Discovery 632
- 10.1.8 Configuration Updates 634
- 10.1.12 Adaptive Mesh Support 635
- 10.2.2 Extended WLANs Only 638
- 10.2.3 Independent WLANs Only 638
- Adaptive AP Pre-requisites 639
- 10.4.2 Switch Configuration 644
- Technical Specifications 655
- A.3 Radio Characteristics 658
- A.4 Antenna Specifications 659
- A.5 Country Codes 663
- Usage Scenarios 667
- Usage Scenarios 669
- B.1.1.3 DHCP Priorities 671
- B.1.2.1 BootP Options 673
- B.1.2.2 BootP Priorities 675
- Customer Support 687
- North American Contacts 688
- International Contacts 688
- Web Support Sites 689
- Additional Information 689
Relacionado con productos y manuales para Puntos de acceso wlan Motorola AP-51XX
(4 paginas)
(4 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.056 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales