Motorola AP-51XX Manual de usuario Pagina 334
- Pagina / 698
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
AP-51xx Access Point Product Reference Guide
7-36
5. Click the Send Cfg to APs button to send the your access point’s configuration to other
access point’s. The recipient access point must be the same single or dual-radio model as
the access point sending the configuration. The sending and recipient access point’s must
also be running the same major firmware version (i.e., 1.1 to 1.1).
6. Click the Start Flash button to flash the LEDs of other access points detected and displayed
within the Known AP Statistics screen.
Use the Start Flash button to determine the location of the devices displayed within the
Known AP Statistics screen. When an access point is highlighted and the Start Flash button
is selected, the LEDs on the selected access point flash. When the Stop Flash button is
selected, the LEDs on the selected access point go back to normal operation.
7. Click the Logout button to securely exit the Access Point applet. A prompt displays
confirming the logout before the applet is closed.
NOTE A ping test initiated from the access point Known AP Statistics screen
uses WNMP pings. Therefore, target devices that are not Motorola access
points are unable to respond to the ping test.
CAUTION When using the Send Cfg to APs function to migrate an access point’s
configuration to other access points, it is important to keep in mind
mesh network configuration parameters do not get completely sent to
other access points. The Send Cfg to APs function will not send the
“auto-select” and “preferred list” settings. Additionally, LAN1 and
LAN2 IP mode settings will only be sent if the sender’s AP mode is
DHCP or BOOTP. The WAN’s IP mode will only be sent if the sender’s IP
mode is DHCP.
!
- Product Reference Guide 1
- AP-51xx Access Point 3
- Product Reference Guide 3
- Contents 5
- Chapter 3. Getting Started 8
- Chapter 5. Network Management 9
- Chapter 8. CLI Reference 11
- Chapter 10. Adaptive AP 13
- Appendix B. Usage Scenarios 14
- Appendix C. Customer Support 14
- About This Guide 15
- Notational Conventions 16
- Service Information 16
- Introduction 17
- 1.1 New Features 18
- 1.1.2 Rogue AP Enhancements 19
- 1.1.5 QBSS Support 19
- 1.2 Feature Overview 20
- 1.2.8.2 EAP Authentication 25
- 1.2.8.3 WEP Encryption 25
- 1.2.8.4 KeyGuard Encryption 26
- 1.2.8.7 Firewall Security 27
- 1.2.8.8 VPN Tunnels 27
- 1.2.8.9 Content Filtering 27
- 1.2.9 VLAN Support 28
- 1.2.11 Updatable Firmware 28
- 1.2.15 Voice Prioritization 30
- 1.2.17 Statistical Displays 31
- 1.2.18 Transmit Power Control 31
- 1.2.22 DHCP Support 32
- 1.2.23 Multi-Function LEDs 33
- 1.2.24 Mesh Networking 33
- 1.2.25 Additional LAN Subnet 34
- 1.2.27 Hotspot Support 35
- 1.3 Theory of Operations 36
- 1.3.1 Cellular Coverage 37
- 1.3.2 MAC Layer Bridging 38
- 1.3.3 Media Types 38
- 1.3.5 MU Association Process 39
- 1.3.6 Operating Modes 40
- Hardware Installation 45
- 2.1 Precautions 46
- Part No. Description 47
- 2.2.2 AP-5181 Configurations 48
- 2.3 Requirements 49
- 2.4 Access Point Placement 49
- 2.4.1 Site Surveys 50
- 2.4.2 Antenna Options 50
- 2.5 Power Options 53
- 2.5.2 AP-5181 Power Options 54
- 2.7 Mounting an AP-5131 57
- Light Pipe 65
- Ceiling Tile 65
- 2.8 AP-5131 LED Indicators 67
- 2.9 Mounting an AP-5181 68
- Attach the square 69
- 2.10 AP-5181 LED Indicators 73
- Data over Ethernet 74
- 802.11a radio activity 74
- 802.11b/g radio activity 74
- 2.11 Setting Up MUs 75
- Getting Started 77
- 3.2 Configuration Options 78
- 3.5.2 Testing Connectivity 90
- 3.5.3 Where to Go from Here? 91
- 4.2 Adaptive AP Setup 98
- 4.3 Configuring Data Access 101
- System Configuration 103
- 4.5 Configuring SNMP Settings 115
- Feature MIB Feature MIB 116
- SNMP v3 user definitions 119
- SNMP access 122
- 4.5.2 Enabling SNMP Traps 123
- 4.7 Logging Configuration 134
- 4.9 Updating Device Firmware 141
- Network Management 149
- 5.2 Configuring WAN Settings 164
- WAN port 167
- 5.2.2 Configuring Dynamic DNS 173
- has data traffic to forward 212
- 6.2 Setting Passwords 221
- New Security Policy screen 224
- 3. Refer to the 246
- 6.10.1.1 Available Protocols 251
- 6.11 Configuring VPN Tunnels 254
- Key Settings screen 264
- 6.11.4 Viewing VPN Status 268
- Details button 278
- 4. Refer to the 279
- Delete-> button 293
- Monitoring Statistics 299
- 7.1 Viewing WAN Statistics 300
- 7.2 Viewing LAN Statistics 304
- 7.3.1 Viewing WLAN Statistics 313
- 7.4.1.1 Retry Histogram 322
- 7.5.1 Viewing MU Details 325
- 7.5.2 Pinging Individual MUs 328
- CLI Reference 335
- 8.1 Connecting to the CLI 336
- 8.2 Admin and Common Commands 337
- AP51xx>admin>help 338
- AP51xx>admin>passwd 339
- AP51xx>admin>summary 340
- AP51xx>admin> 341
- AP51xx>admin> / 342
- AP51xx>admin>save 343
- AP51xx>admin>quit 344
- 8.3 Network Commands 345
- 8.3.1 Network LAN Commands 346
- Description: 347
- Syntax: 347
- Example: 347
- Related Commands: 350
- 8.3.2 Network WAN Commands 374
- 8.3.3.1 Network WLAN Commands 401
- 8.3.3.3 Network ACL Commands 422
- Descripton: 447
- 8.3.5 Network Router Commands 470
- 8.4 System Commands 476
- 8.4.2 System Access Commands 486
- Description: ) 491
- 8.4.4 System SNMP Commands 502
- 8.4.6 System Radius Commands 527
- Description: set 536
- 8.4.8 System Log Commands 555
- 8.5 Statistics Commands 572
- Configuring Mesh Networking 589
- 9.1.5 Normal Operation 594
- 9.3.1.1 Configuring AP#1: 609
- 9.3.1.2 Configuring AP#2 614
- 9.3.1.3 Configuring AP#3 615
- Repeater and a Client Bridge 619
- 9.3.2.1 Configuring AP#1 620
- 9.3.2.2 Configuring AP#2 620
- 9.3.2.3 Configuring AP#3 621
- Adaptive AP 629
- 10.1.1 Where to Go From Here 630
- 10.1.2 Adaptive AP Management 631
- 10.1.3 Types of Adaptive APs 631
- 10.1.4 Licensing 632
- 10.1.5 Switch Discovery 632
- 10.1.8 Configuration Updates 634
- 10.1.12 Adaptive Mesh Support 635
- 10.2.2 Extended WLANs Only 638
- 10.2.3 Independent WLANs Only 638
- Adaptive AP Pre-requisites 639
- 10.4.2 Switch Configuration 644
- Technical Specifications 655
- A.3 Radio Characteristics 658
- A.4 Antenna Specifications 659
- A.5 Country Codes 663
- Usage Scenarios 667
- Usage Scenarios 669
- B.1.1.3 DHCP Priorities 671
- B.1.2.1 BootP Options 673
- B.1.2.2 BootP Priorities 675
- Customer Support 687
- North American Contacts 688
- International Contacts 688
- Web Support Sites 689
- Additional Information 689
Relacionado con productos y manuales para Puntos de acceso wlan Motorola AP-51XX
(4 paginas)
(4 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.079 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales