Motorola AT Commands G24-L Información técnica Pagina 1

TechnicalInformationMOTOROLA G24 DEVELOPER’S GUIDE AT COMMANDS REFERENCE MANUAL ENGLISHJANUARY 31, 20076889192V28-ETitle Page MRC Components OHG, Ob.

Table of Contentsvi AT Commands Reference Manual January 31, 2007Advanced Audio Setup Commands . . . . . . . . . . . . . . . . . . . . . . . . . .

Call Control3-24 AT Commands Reference Manual January 31, 2007The following table shows the +CCWA parameters.Note: When the parameter <mode> is

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-25OKExamples of +CCWA set command - network interrogation AT+CCWA=1,

Call Control3-26 AT Commands Reference Manual January 31, 2007Note: Only voice calls can be put on HOLD.A precondition for the multi-party service is

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-27The following table shows the +CHLD actions according to state and

Call Control3-28 AT Commands Reference Manual January 31, 2007ExampleAT+CHLD=?+CHLD: (0,1,1x,2,2x,3)OKAT+CCWA=1 //Enable call waiting OKatd9311234567

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-29OK+CCWA: "055728386",129,1,"",0 //Waiting cal

Call Control3-30 AT Commands Reference Manual January 31, 2007The following table shows the +CCFC parameters.Note: A forward-to phone <number>

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-31ExampleAT+CCFC=?+CCFC: (0,1,2,3,4,5)OKAT+CCFC=0,3,"0125631683

Call Control3-32 AT Commands Reference Manual January 31, 2007Note: When a service is in state A, and the terminal wants to enable the CLI presentati

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-33RING+CLIP: "",128,,128,"",1)athNO CARRIEROKAT+

Table of ContentsJanuary 31, 2007 AT Commands Reference Manual vii+MKPD, Auxiliary Keypad Control . . . . . . . . . . . . . . . . . . . . . . . . .

Call Control3-34 AT Commands Reference Manual January 31, 2007The following table shows the +CBST parameters.ExampleAT+CBST=?+CBST: (000,004,006,007,

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-35O, Return to Online Data State This command returns the G24 from t

Call Control3-36 AT Commands Reference Manual January 31, 2007+CHUP, Hang Up CallThis command causes the G24 to hang up the current GSM call.+CSNS, S

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-37The following table shows the AT+CSNS parameters.Note: Any mobile-

Call Control3-38 AT Commands Reference Manual January 31, 2007The only +CBST parameter that needs mapping for mobile terminated calls is <speed>

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-39ExampleAT+MDC=?+MDC: (0-1)OKAT+MDC=1OKATD<number>;OKCONNECTA

Call Control3-40 AT Commands Reference Manual January 31, 2007+MFIC, Filtering Incomming CallsThis command instructs the G24 to query or set Filterin

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-41The following table shows the +MFIC parameters.ExampleAT+MFIC=?+MF

Call Control3-42 AT Commands Reference Manual January 31, 2007+MVC, Motorola Vocoders ConfigurationThis AT command is used to choose and configure th

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-43Call Status Messages+CPAS, Phone Activity Status This command disp

Table of Contentsviii AT Commands Reference Manual January 31, 2007Fax Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Call Control3-44 AT Commands Reference Manual January 31, 2007+CLCC, List Current CallsThis command displays a list of all current G24 calls and thei

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-45The following table shows the +CLCC parameters.Note: When a mobile

Call Control3-46 AT Commands Reference Manual January 31, 2007+CLCC: 0OKAT+CLCC=1 //Example with unsolicited indicationOKATD055490698;OK+CLCC: 1,0,2,

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-47+MCST ParametersThe following table shows the +MCST parameters.Exa

Call Control3-48 AT Commands Reference Manual January 31, 2007+MCST: 3+MCST: 17NO CARRIER+MCST: 1+TCLCC, List Current CallsThis command displays a li

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-49The following table shows the +TCLCC parameters.ExampleAT+TCLCC=1O

Call Control3-50 AT Commands Reference Manual January 31, 2007OK+TCLCC: 1,0,4,1,0,,"035659801",1 // Call on holdATD0502147270; // Dial to

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-51The following table shows the +MNTFY parameters.ExampleAT+MNTFY=?+

Call Control3-52 AT Commands Reference Manual January 31, 2007Call Advice of Charge CommandsThis set of commands enables GSM operators to offer Advic

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-53Note: The CCM value depends on the network properties (charge for

Table of ContentsJanuary 31, 2007 AT Commands Reference Manual ixDialing the Last Number Example . . . . . . . . . . . . . . . . . . . . . . . . .

Call Control3-54 AT Commands Reference Manual January 31, 2007+CCCM: "000006"AT+CAOC+CAOC: "000009"OK+CCCM: "00000e"+CC

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-55Refer to “+CAMM, Accumulated Call Meter Maximum”, page 3-55.The fo

Call Control3-56 AT Commands Reference Manual January 31, 2007The following table shows the +CAMM parameters.ExampleAT+CAMM=?OKAT+CAMM="FFFFFF&q

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-57+CPUC, Price per Unit and Currency TableThis command sets the para

Call Control3-58 AT Commands Reference Manual January 31, 2007Note: If <ppu> contains a dot, a maximum of three digits may appear after the dot

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-59OKATD1234567890+CR: REL ASYNCSupplementary ServicesThis set of com

Call Control3-60 AT Commands Reference Manual January 31, 2007The following table shows the +CSSN parameters. Table 3-29:+CSSN Parameters<Paramete

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-61ExampleAT+CSSN=? // test command+CSSN: (0-1),(0-1)OKAT+CSSN=0,0 //

Call Control3-62 AT Commands Reference Manual January 31, 2007+CUSD, Unstructured Supplementary Service DataThis command allows control of Unstructur

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-63ExampleAT+CUSD=?+CUSD: (0,1,2)OKAT+CUSD=1,"*#100#"OK+CUS

Table of Contentsx AT Commands Reference Manual January 31, 2007Controlling the UART Port Speed Within MUX State . . . . . . . . . . . . . . . . . .

Call Control3-64 AT Commands Reference Manual January 31, 2007NETWORK_BUSY 28NOT_SUBSCRIBED 29SERVICE_UNAVAILABLE 31SERVICE_NOT_SUPPORTED 32PREPAY_LI

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-65+COLP, Connected Line Identification PresentationThis command rela

Call Control3-66 AT Commands Reference Manual January 31, 2007The following table shows the +COLP parameters.ExampleAT+COLP=0OKAT+COLP=2+CME ERROR: N

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-67Phone Books and ClockDirectory Access CommandsThis set of commands

Phone Books and Clock3-68 AT Commands Reference Manual January 31, 2007The following table shows the +CPBS parameters.ExampleAT+CPBS="ME"OK

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-69+CPBR, Read Phone Book Entries This command recalls phone book ent

Phone Books and Clock3-70 AT Commands Reference Manual January 31, 2007The following table shows the +CPBR parameters.Note: The MC and RC have the sa

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-71+CPBF, Find Phone Book Entries This execution command enables the

Phone Books and Clock3-72 AT Commands Reference Manual January 31, 2007+CPBF: 2,"8475767800",129,"Moto Voicemail"+CPBF: 101,"

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-73ExampleAt+cpbs="MT"OKAt+cpbw=?+CPBW: (1-750),40,(129,145

January 31, 2007 AT Commands Reference Manual xiFigure No. Figure Title Page No.1-1 System Overview . . . . . . . . . . . . . . . . . . . . . . . . .

Phone Books and Clock3-74 AT Commands Reference Manual January 31, 2007The following table shows the +CSVM parameters.Note: If <mode> is set to

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-75In MUX mode, this AT command is allowed on DLC2 only.Command Type

Phone Books and Clock3-76 AT Commands Reference Manual January 31, 2007The following table shows the +MDSI parameters.ExampleAT+MDSI?+MDSI: 0Table 3-

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-77OKAT+MDSI=?+MDSI: (000,001)OKAT+MDSI=1OK//Until now there was no d

Phone Books and Clock3-78 AT Commands Reference Manual January 31, 2007If only a pair of <mode> and <index> values are given, then the Se

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-79The following table shows the +MCSN parameters.ExampleAT+CNUM // R

Phone Books and Clock3-80 AT Commands Reference Manual January 31, 2007+CNUM: "PIN2","8523",129+CNUM: "","",0

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-81+MPDPM, Motorola Phonebook Dynamic Percentage MemoryThis command r

Phone Books and Clock3-82 AT Commands Reference Manual January 31, 2007OKAT+CPBW=,"035658027",129,"Phone7" OKAT+CPBW=,"03565

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-83The following table shows the +CCLK parameters.ExampleAT+CCLK=?+CC

Phone Books and Clock3-84 AT Commands Reference Manual January 31, 2007AT+CCLKOKAT+CCLK?+CCLK: "05/10/27,16:52:31+08"Power cycling…AT+CCLK?

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-85SMSSMS CommandsG24 supports SMS PDU and SMS TEXT mode according to

SMS3-86 AT Commands Reference Manual January 31, 2007ExampleAT+CSMS=128 +CSMS: 001,001,001OKAT+CSMS? +CSMS: 128,001,001,001OKAT+CSMS=?+CSMS: (128)OK+

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-87The following table shows the +CPMS parameters.Note: The value &ap

SMS3-88 AT Commands Reference Manual January 31, 2007+CMGF, Message Format This command is a basic command. The Set command handles the selection of

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-89The following table shows the +CSCA input characters and their hex

SMS3-90 AT Commands Reference Manual January 31, 2007The following table shows the +CSCA parameters.ExampleAT+CSCA="4252833433"OKAT+CSCA?+C

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-91+CSMP, Set Text Mode ParametersThis command is a basic command and

SMS3-92 AT Commands Reference Manual January 31, 2007ExampleAT+CSMP?+CSMP: 17,167,0,0 (default values for SMS-SUBMIT)OKAT+CSMP= 1,256,0,0+CMS ERROR:

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-93+CSDH, Show Text Mode ParametersThis command controls whether deta

January 31, 2007 AT Commands Reference Manual xiiiTable No. Table Title Page No.1-1 AT Commands . . . . . . . . . . . . . . . . . . . . . . . . . . .

SMS3-94 AT Commands Reference Manual January 31, 2007+CNMI, New Message Indications to Terminal This command handles enabling of unsolicited notifica

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-95AT+CNMI? +CNMI: 0,0,0,0OKAT+CNMI=3,1 OKAT+CMSS=142,"054456503

SMS3-96 AT Commands Reference Manual January 31, 2007When the G24 sends a +CDS response to the terminal, it waits a predefined timeout of 60 seconds

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-97AT+CNMI?+CNMI: 0,0,0,1,0OKAT+CMSS=295+CMSS: 184OK+CDS: 6,184,"

SMS3-98 AT Commands Reference Manual January 31, 2007In text mode: (+CMGF=1):+CMT: <oa>,<scts>[,<tooa>,<fo>,<pid>,<d

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-99AT+CMGS=18 // send to myself> 079179521201009511000c917952446

SMS3-100 AT Commands Reference Manual January 31, 2007Unsolicited Response+CDSI: <mem>,<index>The following table shows the +CDSI paramet

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-101The following table shows the +CDS parameters.After sending a +CD

SMS3-102 AT Commands Reference Manual January 31, 2007The +MMGL command does not change the message status. In addition, +MMGL includes a <stat>

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-103The following table shows the +CGML/+MMGL parameters.Table 3-58:+

List of Tablesxiv AT Commands Reference Manual January 31, 2007Table No. Table Title Page No.3-40 +MDSI Parameters . . . . . . . . . . . . . . . . .

SMS3-104 AT Commands Reference Manual January 31, 2007ExampleAT+CMGL=?+CMGL: ("REC UNREAD","REC READ","STO UNSENT",&quo

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-105+CMGR, +MMGR, Read MessageThese commands handle the reading of SM

SMS3-106 AT Commands Reference Manual January 31, 2007The following table shows the +CMGR parameters. Table 3-59:+CGMR/+MMGR Parameters<Para

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-107Note: Any unused bits will be set to zero and shall be ignored by

SMS3-108 AT Commands Reference Manual January 31, 2007 Table 3-61: <fo> for SMS-DELIVER MessageBit/s Reference Description0-1 Message-Type-Ind

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-109<TP-RA> Mandatory:Recipient address formatted according to

SMS3-110 AT Commands Reference Manual January 31, 2007Note: Reserved bits are ignored.Table 3-63: <fo> for SMS-STATUS-REPORT MessageBit/s Refer

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-111ExampleAT+CPMS?+CPMS: "ME",5,59,"ME",5,59,&qu

SMS3-112 AT Commands Reference Manual January 31, 2007+MMAR, Motorola Mark As Read This command handles changing the <stat> attribute of an SM

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-113When the given index is an incoming message index the header sett

January 31, 2007 AT Commands Reference Manual xv List of TablesTable No. Table Title Page No.3-92 I-PI Serving Cell Miscellaneous Information Screen.

SMS3-114 AT Commands Reference Manual January 31, 2007+CMGW, Write Message to Memory This command is used to write and save a message to <mem2>

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-115Table 3-68: Layout of SMS-SUBMIT in PDU Mode: (according to GSM03

SMS3-116 AT Commands Reference Manual January 31, 2007<TP-CDL> Command data length 1 BYTE<TP-CD> Command data 0-156 BYTESTable 3-70: <

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-117Note: Any unused bits will be set to 0.ExampleAT+CMGF=1OKAT+CMGW=

SMS3-118 AT Commands Reference Manual January 31, 200700410042004300440045OKAT+CSMP=25,"05/03/15,21:22:23+08",0,0OKAT+CMGW="0544565034

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-119+CMGD, Delete Message This command handles deletion of a single m

SMS3-120 AT Commands Reference Manual January 31, 2007+CGSMS, Select Service for MO SMS MessagesThis command handles the selection of the service or

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-121+CMGS, Send SM to NetworkThis command sends an SM from the G24 to

SMS3-122 AT Commands Reference Manual January 31, 2007If after aborting AT+CMGS command execution and before result of operation was reported by G24,

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-123The following table shows the AT+CSCB parameters.Notes:• A combin

SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICENoticeWhile reasonable efforts have been made to assure the accuracy of this document, Motorola, Inc. a

List of Tablesxvi AT Commands Reference Manual January 31, 2007Table No. Table Title Page No.3-144 +CRTT Parameters . . . . . . . . . . . . . . . . .

SMS3-124 AT Commands Reference Manual January 31, 2007OKAdding channels 3, 4,5,6,22 to mid list and languages 1,8 to dcs list:AT+CSCB=0,"3-6,22&

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-125The following table shows the +MCSAT parameters.Table 3-76:+MCSAT

SMS3-126 AT Commands Reference Manual January 31, 2007ExampleAT+MCSAT=?+MCSAT:(0-2)OKAT+MCSAT?+MCSAT: 1OKAT+MCSAT=2OKAT+MCSAT=1,00001000 // UCS2

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-127+TSMSRET, Control SMS Sending RetryThis command controls the SMS

SMS3-128 AT Commands Reference Manual January 31, 2007Table 3-79 shows the conversion between the <dcs> and +CSCS setting when storing SM to m

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-129Table 3-80 shows the conversion between the <dcs> and +CSCS

SMS3-130 AT Commands Reference Manual January 31, 2007OKAT+CMGR=223+CMGR: "STO UNSENT","0544565803",050003090301123456786543FEOKA

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-131AT+CMGR=227+CMGR: "STO UNSENT","0544565803",A

Network3-132 AT Commands Reference Manual January 31, 2007NetworkNetwork Commands+CSQ, Signal Strength This command displays the received signal stre

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-133+CRLP, Radio Link ProtocolThis command displays the Radio Link Pr

January 31, 2007 AT Commands Reference Manual xvii List of TablesTable No. Table Title Page No.3-196 +CGEQREQ Command Parameters. . . . . . . . . . .

Network3-134 AT Commands Reference Manual January 31, 2007+CREG, Network Registration StatusThe following table shows the +CREG parameters.Command Ty

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-135ExampleAT+CREG=? +CREG: (000 - 002)OK AT+CREG? +CREG: 000,001 OK

Network3-136 AT Commands Reference Manual January 31, 2007+CGREG, GPRS Network Registration The following table shows the +CGREG parameters.Command T

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-137ExampleAT+CGREG=?+CGREG: (000-002)OKAT+CGREG=2OKAT+CGREG?+CGREG:

Network3-138 AT Commands Reference Manual January 31, 2007Command TypeSyntax Response/Action RemarksSetAT+COPS=[<mode>[,<format>[,<ope

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-139The following table shows the +COPS parameters.ExampleAT+COPS=? +

Network3-140 AT Commands Reference Manual January 31, 2007+CPOL, Preferred OperatorsThis command is used to edit the list of preferred network operat

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-141The following table shows the +CPOL parameters.Note: To delete an

Network3-142 AT Commands Reference Manual January 31, 2007+MFS, Motorola Frequency of SearchThis command is used to determine how long the G24 waits

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-143The following table shows the +MFS parameters. ExampleAT+MFS=? /

Network3-144 AT Commands Reference Manual January 31, 2007+MCELL, Motorola Cell DescriptionThis command displays information about the Cellular Netwo

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-145 ExampleAT+MCELL = 0,1+MCELL: Serving Idle/PIBC0077s* 50-071BBC00

Network3-146 AT Commands Reference Manual January 31, 2007+33 *** pc* +33 4n0084s* 17-096B+06 *** pc* +06 t00r00mtp33 -102cba0cbq0 GP rSOKAT+MCELL =

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-147Table 3-91: Circuit Switched Serving Cell Information ScreenTable

Network3-148 AT Commands Reference Manual January 31, 2007Table 3-94: TBF Downlink Data Transfer ScreenTable 3-95: Neighbor Cell Information ScreenTa

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-149Table 3-97: Reselection ScreenTable 3-98: Hopping Information Scr

Network3-150 AT Commands Reference Manual January 31, 2007Table 3-100: I-PI Serving Cell Paging Parameters ScreenTable 3-101: I-PI Serving Cell Optio

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-151The following table provides definitions for EFEM-related terms.T

Network3-152 AT Commands Reference Manual January 31, 2007Cell ID Cell Identity parameter, from System Info 3.CellResHys Cell reselect hysteresis, us

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-153Max bit rate dl Max bit rate for Downlink in KPBS.Max bit rate ul

January 31, 2007 AT Commands Reference Manual xixPrefaceManual ScopeThis manual introduces the G24 AT commands, and describes how software developers

Network3-154 AT Commands Reference Manual January 31, 2007split_pg_cycle Number of paging blocks to read on the serving cell in each row of 64 multif

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-155+MCI, Motorola Cell InformationThis command returns neighbor cell

Network3-156 AT Commands Reference Manual January 31, 2007The following table shows the +MCI parameters.ExampleAT+MCI // Get the current serving and

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-157AT+MCI? // Get current set <Filter> and <enable TA>

Hardware Information3-158 AT Commands Reference Manual January 31, 2007Hardware InformationHardware Information Commands+CBC, Battery Charger Connect

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-159Note: The battery level is an average value, which updated once i

Hardware Information3-160 AT Commands Reference Manual January 31, 2007The following table shows the +CBAUD parameters.ExampleAT+CBAUD=57600orAT+CBAU

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-161Using AT+IPR=<rate> with a <rate> value other than 9

Hardware Information3-162 AT Commands Reference Manual January 31, 2007+GCAP, Request Overall Capabilities This command indicates the major capabilit

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-163+MTCTS, CTS Line Test CommandThis command sets the CTS pin of the

Applicable Documentsxx AT Commands Reference Manual January 31, 2007Applicable Documents• G24 Module Hardware Description – 6889192V27• G24 Developer

Hardware Information3-164 AT Commands Reference Manual January 31, 2007The following table shows the &K parameters.ExampleAT&K?&K: 3OKAT&

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-165The following table shows the &C parameters.Note: If &C i

Hardware Information3-166 AT Commands Reference Manual January 31, 2007&D, Circuit 108 BehaviorThis command determines how the G24 responds when

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-167+MCWAKE, GPRS CoverageThis command tells the G24 whether to repor

Hardware Information3-168 AT Commands Reference Manual January 31, 2007+MGGIND, GSM/GPRS Service IndicatorThis command configures the service indicat

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-169+CFUN, Shut Down Phone FunctionalityThis command shuts down the p

Hardware Information3-170 AT Commands Reference Manual January 31, 2007AT+CFUN?+CFUN: 4Power cycling…AT+CFUN?+CFUN: 4Power cut …AT+CFUN? // Phone t

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-171The following table shows the +ICF parameters.ExampleAT+ICF?+ICF:

Hardware Information3-172 AT Commands Reference Manual January 31, 2007The following table shows the ATS97 parameters. Example// Connect the antennaA

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-173Operation of this command is flex dependant.The following table s

Preface January 31, 2007 AT Commands Reference Manual xxiManual Banner DefinitionsA banner text in the page footer under the book title (for example,

Hardware Information3-174 AT Commands Reference Manual January 31, 2007+TWUR, Wakeup Reason RequestThis command is used to query the wakeup reason. M

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-175Operation of this command is flex dependant.The following table s

Hardware Information3-176 AT Commands Reference Manual January 31, 2007Operation of this command is flex dependant.The following table shows the +TAD

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-177In case that second UART is open for full functionality, the call

Hardware Information3-178 AT Commands Reference Manual January 31, 2007ExampleAT+MPSU? +MPSU: 0OKAT+MPSU=?+MPSU: (0-2)OKAT+MPSU=2OK/* reset and after

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-179The following table shows the +MIOC parameters.Table 3-121: +MIOC

Hardware Information3-180 AT Commands Reference Manual January 31, 2007ExampleAT+MIOC=?+MIOC: (00000000-11111111),(00000000-11111111)OKLight control

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-181Data sending (vectoe example):Client has a data bus with 8 bits a

Hardware Information3-182 AT Commands Reference Manual January 31, 2007+MIOD, Motorola I/O DefineThis command defines the G24 8 GPIO pins configurati

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-183The following table shows the +MIOD parameters.The following tabl

Caring for the Environmentxxii AT Commands Reference Manual January 31, 2007Keep away from live circuitsOperating personnel must:• not remove equipme

Hardware Information3-184 AT Commands Reference Manual January 31, 2007Example+MIOD: (00000000-11111111),(0,1),( 00000000-11111111)AT+MIOD=00010000,0

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-185The following table shows the +MMAD parameters.ReadAT+MMAD? List

Hardware Information3-186 AT Commands Reference Manual January 31, 2007Table 3-125: A/D Value to Temperature ConversionTemperature(°C)ADValue-decimal

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-187Figure 3-1: Temperatur Vs. A/D ValueTemperature Conversion Functi

Hardware Information3-188 AT Commands Reference Manual January 31, 2007+MMAD:4,0,1,0,255+MMAD:5,0,1,300,450OKAT+MMAD=? //Test command - range of all

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-189AT+MPCMC?+MPCMC: 1OKAT+MPCMC=0OKAT+MPCMC?+MPCMC: 0OK+MVREF, Motor

Hardware Information3-190 AT Commands Reference Manual January 31, 2007ExampleAT+MVREF=?+MVREF:(0-2)OKAT+MVREF=1OKAT+MVREF?+MVREF: 1OKAT+MVREF=2 //Th

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-191AudioScopeThe audio control can be Summarized to the following th

Audio3-192 AT Commands Reference Manual January 31, 2007Table 3-129 shows the differences between Basic and Advanced audio modes in controlling the a

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-193Audio Control of Path, Gain and Algorithms is available by these

Preface January 31, 2007 AT Commands Reference Manual xxiiiPlease contact the Customer Network Resolution Center (CNRC) for assistance. The 24 hour t

Audio3-194 AT Commands Reference Manual January 31, 2007G24 supports both analog and digital audio. Digital audio is supported in both basic and adva

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-195The following table shows the +CRSL parameters.ExampleAT+CRSL?+CR

Audio3-196 AT Commands Reference Manual January 31, 2007ExampleAT+CLVL?+CLVL: 7OKAT+CLVL=?+CLVL: (0-7)OKAT+CLVL=3OK+CMUT, Mute/Unmute Currently Activ

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-197OKAT+CMUT =2+CME ERROR: <err>S94, Sidetone EffectThis comma

Audio3-198 AT Commands Reference Manual January 31, 2007ATS94=2+CME ERROR: <err>ATS94? 000 //Sidetone disabledOKS96, Echo CancelingThis command

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-199OKATS96=4+CME ERROR: <err>ATS96?001 //Echo canceling enable

Audio3-200 AT Commands Reference Manual January 31, 2007The following diagram shows the audio paths:.Figure 3-6: Audio PathsCommand TypeSyntax Respon

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-201The following table shows the +MAPATH parameters.ExampleAT+MAPATH

Audio3-202 AT Commands Reference Manual January 31, 2007+MAVOL, Volume Setting This command enables you to determine a volume level for a particular

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-203The following table shows the +MAVOL parameters.Example//Set volu

How to Get Warranty Service?xxiv AT Commands Reference Manual January 31, 2007Warranty Term, and must immediately submit the Product for service to M

Audio3-204 AT Commands Reference Manual January 31, 2007+MAMUT, Input Devices Mute This command controls the muting/unmuting of all input paths (mic,

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-205+MAFEAT, Features SelectionThis command controls the algorithm fe

Audio3-206 AT Commands Reference Manual January 31, 2007General Audio Commands+MADIGITAL, Analog/Digital Audio SwitchingThis command switches between

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-207+CALM, Alert Sound ModeThis command handles the selection of the

Audio3-208 AT Commands Reference Manual January 31, 2007+ MMICG, Microphone Gain ValueThis command handles the selection of microphone gain values of

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-209+CRTT, Ring Type SelectionThis command plays one cycle of a ring

Audio3-210 AT Commands Reference Manual January 31, 2007ExampleAT+CRTT=6,0 //Ring type number 6, operation 0 (play)OK //When 6 is in the supported &l

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-211+VTD, Tone DurationThis command handles the selection of tone dur

Audio3-212 AT Commands Reference Manual January 31, 2007+VTS, Command-Specific Tone DurationThis command transmits a string of DTMF tones when a voic

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-213AccessAccess Control CommandsWhen the phone or SIM card is locked

Preface January 31, 2007 AT Commands Reference Manual xxvIn some cases, you may be requested to provide additional information concerning the mainten

Access3-214 AT Commands Reference Manual January 31, 2007+CPIN, Enter PIN for Unlocking SIM Card or Enter PUK for Unblocking SIM Card This command lo

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-215The following table shows the +CPIN parameters.Command Type Synta

Access3-216 AT Commands Reference Manual January 31, 2007ExampleAT+CPIN=? OKAT+CLCK="SC",1,"<correct PIN>"//Not case-sensit

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-217+EPIN, Enter SIM PIN2 to Verify PIN2 IndicatorThis AT command wil

Access3-218 AT Commands Reference Manual January 31, 2007+TPIN, Query Number of Remaining SIM PIN/PUK Entering AttemptsThis command returns the numbe

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-219+CPWD, Change PasswordThis command sets a new password for the fa

Access3-220 AT Commands Reference Manual January 31, 2007ExampleAT+CPWD =? +CPWD: ("SC",8),("AO",8),("OI",8),("OX&

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-221The following table shows the +CLCK parameters.Command Type Synta

Access3-222 AT Commands Reference Manual January 31, 2007ExampleAT+CLCK=?+CLCK: ("SC","AO","OI","OX","AI

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-223OK(Voice and data international calls barred, fax and SMS not bar

Trademarks MOTOROLA and the Stylized M Logo are registered in the US Patent & Trademark Office. All other product or service names are the propert

Installed Dataxxvi AT Commands Reference Manual January 31, 20076. Defects or damage due to range, coverage, availability, grade of service, or opera

Access3-224 AT Commands Reference Manual January 31, 2007The following table shows the +EMPC parameters.ExampleAT+EMPC?+EMPC:3,0OKThe status of phone

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-225AT+EMPC="<wrong pin>",0+EMPC:2,1OKThe phone moves

Modem Configuration and Profile3-226 AT Commands Reference Manual January 31, 2007Modem Configuration and Profile Modem Register CommandsThe G24 hold

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-227The following table shows the V parameters.ExampleATV?V: 1OKATV00

Modem Configuration and Profile3-228 AT Commands Reference Manual January 31, 2007The following table shows the Qn parameters.ExampleATQ0OKATQ?Q: 0OK

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-229ExampleATE?001OKX, Result Code Selection and Call Progress Monito

Modem Configuration and Profile3-230 AT Commands Reference Manual January 31, 2007S, Bit Map RegistersThis command reads/writes values of the S-regis

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-231The following table shows the different S-registers and their ass

Modem Configuration and Profile3-232 AT Commands Reference Manual January 31, 2007ExampleATS36?005OKATS0=3OKATS0?003OKS2This command handles the sele

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-233S12This command handles the selection of the guard time, which is

Preface January 31, 2007 AT Commands Reference Manual xxviiRevision HistoryManual Number6889192V28-EManual TitleG24 Developer’s Guide: AT Commands Re

Modem Configuration and Profile3-234 AT Commands Reference Manual January 31, 2007?, Return the Value of the Last Updated S-registerThis command disp

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-235ExampleAT&F?&F: 0OKZ, Reset to Default ConfigurationThis

Modem Configuration and Profile3-236 AT Commands Reference Manual January 31, 2007sleep mode and signals its readiness for sleep. For this purpose, a

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-237Figure 3-9: Wakeup-In LineTwo modes exist:• Idle Mode: The termin

Modem Configuration and Profile3-238 AT Commands Reference Manual January 31, 2007Two modes exist:• Idle mode: The G24 has no data to send.• Wakeup m

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-239The following table shows the S24 parameters.ExampleATS24? <en

Modem Configuration and Profile3-240 AT Commands Reference Manual January 31, 2007The following table shows the S102 parameters.ExampleATS102? <en

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-241Exampleats100?001OKats100=0OKats100?000OK+MSCTS, Enable/Disable C

Modem Configuration and Profile3-242 AT Commands Reference Manual January 31, 2007The following table shows the +MSCTS parameters.ExampleAT+MSCTS = ?

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-243The following table shows the +CMEE parameters. Command Type S

Modem Configuration and Profile3-244 AT Commands Reference Manual January 31, 2007 Table 3-169: +CME Errors<Parameter> Description<err>

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-245Note: +CME ERROR:280, Data lost, is sent to the terminal in extr

Modem Configuration and Profile3-246 AT Commands Reference Manual January 31, 2007 Table 3-170: +CMS Errors<Parameter> Description<err>

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-247ExampleAT+CMEE=0 //+CME ERROR is not usedOKAT+VTDERRORAT+CMEE=1

Modem Configuration and Profile3-248 AT Commands Reference Manual January 31, 2007+CEER, Extended Error ReportThis execution command returns an exten

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-249The following table shows the +CEER parameters.Table 3-171: +CEER

Modem Configuration and Profile3-250 AT Commands Reference Manual January 31, 2007ExampleAt+CEER+CEER: "No information available"OK AT+CEER

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-251+MGEER, GPRS Extended Error ReportThis command is used to return

Modem Configuration and Profile3-252 AT Commands Reference Manual January 31, 2007The following table shows the +MGEER parameters.Table 3-172: +MGEER

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-253ExampleAT+MGEER=2OKAT+MGEER+MGEER: NO INFORMATION AVAILABLEOKAT+M

January 31, 2007 AT Commands Reference Manual 1-1Chapter 1: Product FeaturesConnectivity InterfaceThe user can establish two types of connections in o

UI (User Interface)3-254 AT Commands Reference Manual January 31, 2007UI (User Interface)+CRSM, Restricted SIM AccessThis command provides limited ac

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-255The following table shows the +CRSM parameters.Table 3-173: +CRSM

UI (User Interface)3-256 AT Commands Reference Manual January 31, 2007<P1>,<P2>,<P3>Integer type. Parameters passed on by the ME to

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-257<sw1> <sw2> Integer character format. Information, fr

UI (User Interface)3-258 AT Commands Reference Manual January 31, 2007ExampleAT+CRSM=176,28478,0,0,20 //READ BINARY, GID1(6F3E),0 ,0 , 20 bytes+CRSM:

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-259+CRSM: 152,4 //Error: access condition not fulfilledOKAT+CRSM=220

UI (User Interface)3-260 AT Commands Reference Manual January 31, 2007Exampleat&vACTIVE PROFILE:E1 Q0 V1 X4 &C1 &D2 &K3 &Y0S00:00

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-261ExampleAT&W0OKAT&W1OKAT&C Set circuit 109 (DCD) behav

&Y, Default User ProfileThe following table shows the &Y parameters.ExampleAT&Y0OKAT&Y1OK+CKPD, Keypad Control This command emulates k

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-263commands like ATH/AT+CHLD and so on.Note: The +CKPD command does

CSD Operation1-2 AT Commands Reference Manual January 31, 20072. Upon being interrupted by the RI signal, drop the DTR line to switch to command mode

UI (User Interface)3-264 AT Commands Reference Manual January 31, 2007ExampleAT+CMER=0,2,0,0,0OKAT+CKPD=m //Emulate pressing the MENU buttonOK+CKEV:

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-265The following table shows the +MKPD parameters.ExampleAT+CMER=0,2

UI (User Interface)3-266 AT Commands Reference Manual January 31, 2007+CMER, Mobile Equipment Event ReportingThe following table shows the +CMER para

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-267+CLAN, ME LanguageThis command handles the selection of language

UI (User Interface)3-268 AT Commands Reference Manual January 31, 2007ExampleAT+CLAN?+CLAN: "EN"OK AT+CLAN=?+CLAN: "DE","EN&

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-269The following table shows the +CIND parameters.ExampleAT+CIND=?+C

UI (User Interface)3-270 AT Commands Reference Manual January 31, 2007Unsolicited UI Status MessagesCertain actions performed in the G24 UI by the us

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-271+CDEV, Change Display IndicationWhen text on the display changes

+MUPB, Phone Book Event This output is sent by the G24 when a phone book entry is accessed or modified.Unsolicited Report+MUPB: <event>,<inde

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-273GPRS/EDGEGPRS FunctionalityGSM 07.07 defines commands that a TE m

Chapter 1: Product Features January 31, 2007 AT Commands Reference Manual 1-3Service Provider (ISP) to send email or dialing the corporate Intranet t

GPRS/EDGE3-274 AT Commands Reference Manual January 31, 2007+CGCLASS, GPRS Mobile Station ClassThis command is used to set the G24 to operate accordi

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-275+CGDCONT, Define PDP ContextThis command specifies the PDP (Packe

GPRS/EDGE3-276 AT Commands Reference Manual January 31, 2007The following table shows the +CGDCONT parameters.Note: The IP address may be entered wit

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-277+CGDCONT: 3,"IP","","0.0.0.0",0,0OK

GPRS/EDGE3-278 AT Commands Reference Manual January 31, 2007The following table shows the +CGQMIN parameters.ReadAT+CGQMIN? +CGQMIN: <cid>, <

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-279ExampleAT+CGQMIN=?+CGQMIN: ("IP"),(0-3),(0-4),(0-5),(0-

GPRS/EDGE3-280 AT Commands Reference Manual January 31, 2007The following table shows the +CGQREQ parameters.ExampleAT+CGQREQ=?+CGQREQ: ("IP&quo

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-281Note: This command has the characteristics of both the V.25ter ac

GPRS/EDGE3-282 AT Commands Reference Manual January 31, 2007D*99, Request GPRS Service "D"This command enables the ME to perform the action

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-283The following table shows the D*99 parameters.ExampleATD*99 //Try

Improved OEM Features1-4 AT Commands Reference Manual January 31, 2007TCP/IPWhen establishing the TCP/IP connection the G24 can only be the "ini

GPRS/EDGE3-284 AT Commands Reference Manual January 31, 2007+CGPRS, GPRS CoverageThis command indicates whether there is GPRS coverage.Note: GPRS/EDG

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-285+CGACT, PDP Context Activate or DeactivateThis command activates/

GPRS/EDGE3-286 AT Commands Reference Manual January 31, 2007ExampleAT+CGACT=?+CGACT: (0,1)OKAT+CGACT?+CGACT: 1,0+CGACT: 2,0+CGACT: 3,0OKAT+CGACT=1ERR

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-287The following table shows the +CGPADDR parameters.ExampleAT+CGPAD

GPRS/EDGE3-288 AT Commands Reference Manual January 31, 2007EDGE CommandsNote: The following commands will be used only with G24 modules that support

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-289Read+CGEQREQ? +CGEQREQ: <cid>, <Traffic class> ,<M

GPRS/EDGE3-290 AT Commands Reference Manual January 31, 2007Test+CGEQREQ=? +CGEQREQ: <PDP_type>, (list of supported <Traffic class>s) ,(l

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-291The following table shows the +CGEQREQ command parameters.Table 3

GPRS/EDGE3-292 AT Commands Reference Manual January 31, 2007<Delivery order> Numeric parameter that indicates whether the EDGE bearer shall pro

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-293ExampleSet commands:AT+CGEQREQ=1,1,64,64,64,64,1,0,"1E4"

Chapter 1: Product Features January 31, 2007 AT Commands Reference Manual 1-5UDP/IPThe set of AT commands created for the TCP/IP connection is used f

GPRS/EDGE3-294 AT Commands Reference Manual January 31, 2007+CGEQMIN, (Minimum acceptable)This command allows the TE to specify a minimum acceptable

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-295Read+CGEQMIN? +CGEQMIN: <cid>, <Traffic class> ,<M

GPRS/EDGE3-296 AT Commands Reference Manual January 31, 2007Test+CGEQMIN=? +CGEQMIN: <PDP_type>, (list of supported <Traffic class>s) ,(l

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-297The following table shows the +CGEQMIN command parameters.Table 3

GPRS/EDGE3-298 AT Commands Reference Manual January 31, 2007<Delivery order> Numeric parameter that indicates whether the EDGE bearer shall pro

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-299ExampleSet commands:AT+CGEQMIN=1,1,64,64,64,64,1,0,"1E4"

GPRS/EDGE3-300 AT Commands Reference Manual January 31, 2007+CGEQNEG - (Negotiated)This command allows the TE to retrieve the negotiated QoS profiles

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-301The following table shows the +CGEQNEG command parameters.Table 3

GPRS/EDGE3-302 AT Commands Reference Manual January 31, 2007<Delivery order> Numeric parameter that indicates whether the EDGE bearer shall pro

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-303ExampleAT+CGDCONT=1,"IP","INTERNETG"OKAT+CGAC

Improved OEM Features1-6 AT Commands Reference Manual January 31, 20075. Server side: – After receiving the first packet from the client, the server

GPRS/EDGE3-304 AT Commands Reference Manual January 31, 2007+MCEG, Motorola Control EGPRSThis AT command is used to enable or disable EGPRS support i

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-305TCP/IP+MIPCALL, Create a Wireless LinkThis command sets up a PPP

GPRS/EDGE3-306 AT Commands Reference Manual January 31, 2007ExampleAT+MIPCALL=1,"internet","User1","Pswd"//Connecting t

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-307The following table shows the +MIPOPEN parameters.Note: Motorola

GPRS/EDGE3-308 AT Commands Reference Manual January 31, 2007// Listen socket over TCP:AT+MIPOPEN=1,1100,"0.0.0.0",0,0 // Listens to any por

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-309The following table shows the +MIPODM parameters.Note: Motorola d

GPRS/EDGE3-310 AT Commands Reference Manual January 31, 2007Enter invalid command format:AT+MIPODMERRORCheck opened in Online Data Mode socket state

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-311The following table shows the +MIPCLOSE parameters.ExampleAT+MIPC

GPRS/EDGE3-312 AT Commands Reference Manual January 31, 2007+MIPSETS, Set Size for Automatic PushThis command causes the G24 to set a watermark in th

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-313+MIPSETS: (1-4),(1-1372)OKAT+MIPSETS?+MIPSETS: 1,100 //Informatio

Chapter 1: Product Features January 31, 2007 AT Commands Reference Manual 1-7Features and BenefitsThe TCP/UDP IP feature provides the terminal with t

GPRS/EDGE3-314 AT Commands Reference Manual January 31, 2007Example(Socket 4 was not opened using +MIPOPEN AT command) AT+MIPSEND=4,"4444"E

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-315The following table shows the +MIPPUSH parameters.ExampleAT+MIPPU

GPRS/EDGE3-316 AT Commands Reference Manual January 31, 2007ExampleAT+MIPFLUSH=2 //Socket number 2 was previously opened using the +MIPOPEN command+M

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-317The following table shows the +MIPRTCP parameters.Example+MIPRTCP

GPRS/EDGE3-318 AT Commands Reference Manual January 31, 2007Syntax+MIPDATA: <Socket ID>,<Number of received data bytes>The following tabl

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-319MIPCONF - Configure Internal TCP/IP stackThis command allows to c

GPRS/EDGE3-320 AT Commands Reference Manual January 31, 2007ExampleAT+MIPCONF=2,5,10,600,75,2OKAT+MIPOPEN=2,0,"66.249.87.99",80,0OK+MIPOPEN

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-321+MIPRTCP: 2,130,484541443E3C5449544C453E333032204D6F7665643C2F544

GPRS/EDGE3-322 AT Commands Reference Manual January 31, 2007The following table shows the +MPING command parameters.Read+MPING? +MPING: <count>

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-323<TTL> Time To Live (TTL). Specifies number of hops (hop is

Improved OEM Features1-8 AT Commands Reference Manual January 31, 2007Features and BenefitsThe following algorithm related features are provided:Side

GPRS/EDGE3-324 AT Commands Reference Manual January 31, 2007The following table shows the +MPING unsolicited response parameters.Notes:1. Ping reques

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-325ExampleAT+MIPCALL=1,"internet"OK+MIPCALL: 10.170.4.111A

GPRS/EDGE3-326 AT Commands Reference Manual January 31, 2007The following table shows the +MPINGSTAT unsolicited response parameters.Table 3-215:+MPI

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-327ExampleAT+MIPCALL=1,"internet"OK+MIPCALL: 10.170.4.111/

GPRS/EDGE3-328 AT Commands Reference Manual January 31, 2007+MSDNS, Set DNS IP AddressThis command set/read DNS (Domain Name Server) IP address (prim

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-329ExampleAT+MSDNS=?+MSDNS: (1-5),(<IP>),(<IP>)OKAT+MSDN

GPRS/EDGE3-330 AT Commands Reference Manual January 31, 2007OKAT+MSDNS?+MSDNS: 1,"192.118.9.177","192.118.11.77"+MSDNS: 2,"1

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-331NOP - CompatibleIGNORED (Compatible Only) CommandsThe following c

Fax Class 13-332 AT Commands Reference Manual January 31, 2007Fax Class 1Facsimile machines were developed for sending digitized documents over the G

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-333Fax Commands+FCLASS, Select ModeThe G24 facsimile service maintai

Chapter 1: Product Features January 31, 2007 AT Commands Reference Manual 1-9Noise SuppressNoise suppression improves audio quality in all modes by s

Fax Class 13-334 AT Commands Reference Manual January 31, 2007+FTS, Transmit SilenceThis command causes the G24 to stop any transmission. The G24 the

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-335The following table shows the +FRS parameters.ExampleAt+fclass=1O

Fax Class 13-336 AT Commands Reference Manual January 31, 2007The following table shows the command modulation select codes.ExampleAT+FCLASS=1OKATD03

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-337+FRM, Receive DataThis command causes the G24 to receive data fro

Fax Class 13-338 AT Commands Reference Manual January 31, 2007After the entering active session mode (G24 sent CONNECT to the terminal), the terminal

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-339+FRH, Receive DATA with HDLC FrameThis command causes the G24 to

Fax Class 13-340 AT Commands Reference Manual January 31, 2007The implementation of this parameter is mandatory if V.42 error control or Buffered mod

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-341+FPR, Fax Serial Port RateThis command sets the request baud rate

Fax Class 13-342 AT Commands Reference Manual January 31, 2007ExampleExample - AT+FCLASS=1 OKAT+FPR=8OKAT+FPR? +FPR: 8OKAT+IPR=300OkAT+FPR?+FPR:255O

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-343RS232 Multiplexer FeatureThe MUX provides multiple logical commun

MUX Integration1-10 AT Commands Reference Manual January 31, 2007MUX IntegrationOverviewThe G24 is supplied with an internal GSM 7.10 protocol stack,

RS232 Multiplexer Feature3-344 AT Commands Reference Manual January 31, 2007Product ArchitectureThe following figure shows the former architecture (P

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-345Figure 3-16: MUX StatesPREMUX StateOnce the GRLC logical communic

RS232 Multiplexer Feature3-346 AT Commands Reference Manual January 31, 2007UART Flow ControlThe following sections describe UART flow control in the

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-347+CMUX, MUX Startup Command This command is used to enable/disable

RS232 Multiplexer Feature3-348 AT Commands Reference Manual January 31, 2007The following table shows the +CMUX parameters.Note: Due to non-ERM, the

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-349MUX Customer Open Source Code PacketThe MUX is provided with an o

RS232 Multiplexer Feature3-350 AT Commands Reference Manual January 31, 2007Multiple Channel Configuration The configurations listed below are recomm

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-351DLC1 Explanation:An external host interface is used as a regular

RS232 Multiplexer Feature3-352 AT Commands Reference Manual January 31, 2007Table 3-226: AT Commands Limitations for 4-Channel ConfigurationIDLC-1 ID

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-353+CBAND V Ignored+CBAUD V MUX degeneratedYes+CBC V Yes+CBST V csd

Chapter 1: Product Features January 31, 2007 AT Commands Reference Manual 1-11• Receive Incoming SMS indication• Inquiry GSM coverage indication• Set

RS232 Multiplexer Feature3-354 AT Commands Reference Manual January 31, 2007+CIMI V Yes+CIND V Yes PCHS - unsolicited+CKEV V Yes PCHS - unsolicited+C

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-355+CNMI V Yes Unsolicited - special+CNUM V Yes+COLP V Yes PCHS - un

RS232 Multiplexer Feature3-356 AT Commands Reference Manual January 31, 2007+CSVM V Yes+CTFR1VVVV+CUSD V Yes+EPINVVVV Yes+FCLASS V csd V Yes PCHS+FMI

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-357+MCELLVVVV Yes+MCSAT V+MCSN V+MCST V Yes PCHS - unsolicited+MCWAK

RS232 Multiplexer Feature3-358 AT Commands Reference Manual January 31, 2007+MMGR V Yes+MMICG V Yes+MNTFY V Yes+MPCM V+MPCMC V Yes+MPDPM V Yes+MPING

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-359AVVVVAnswers only a "self" ringing call. Refer to the R

RS232 Multiplexer Feature3-360 AT Commands Reference Manual January 31, 2007S7VVVV YesPCHSS94VVVV YesS96VVVV YesS97VVVVTVVVVIgnoredVVVVV YesPCHSXVVVV

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-361Multiple Channel DefinitionsThe following table provides various

RS232 Multiplexer Feature3-362 AT Commands Reference Manual January 31, 2007IDLC Modem Profile in MUX StateDefinitions• Modem profile – G24 modem set

January 31, 2007 AT Commands Reference Manual 4-1Chapter 4: Using the CommandsSetting Up the G24 (Power On and Initial Actions)There are three phases

Short Message Service (SMS)1-12 AT Commands Reference Manual January 31, 2007Short Message Service (SMS)OverviewThe SMS feature provides means for SM

Setting Up the G24 (Power On and Initial Actions)4-2 AT Commands Reference Manual January 31, 2007Figure 4-2: Detailed Phone State TransactionsReadyG

Chapter 4: Using the Commands January 31, 2007 AT Commands Reference Manual 4-3Recommended G24 Initialization after PowerupFigure 4-3 provides a reco

Recommended G24 Initialization after Powerup4-4 AT Commands Reference Manual January 31, 2007RS232 Lines SetupThere is no dynamic detection. Upon pow

Chapter 4: Using the Commands January 31, 2007 AT Commands Reference Manual 4-5Test G24 CommunicationThis is a preliminary step. During this step, th

Recommended G24 Initialization after Powerup4-6 AT Commands Reference Manual January 31, 20071. Baud setting example:AT+CBAUD=6//Setting baud rate fo

Chapter 4: Using the Commands January 31, 2007 AT Commands Reference Manual 4-7SIM Card StatusTo enable the module to transfer from basic commands to

Recommended G24 Initialization after Powerup4-8 AT Commands Reference Manual January 31, 2007G24 Network ConnectionIn this step, the G24 detects exis

Chapter 4: Using the Commands January 31, 2007 AT Commands Reference Manual 4-9Terminal SynchronizationIn this step, the terminal requests the stored

SMS4-10 AT Commands Reference Manual January 31, 2007SMSManaging Stored Messages in the G24 MemoryAT+CPMS="me" //Select NVM as preferred m

Chapter 4: Using the Commands January 31, 2007 AT Commands Reference Manual 4-11Setting the Notification Indication for Incoming Messages (Using AT+C

Chapter 1: Product Features January 31, 2007 AT Commands Reference Manual 1-13Technical DescriptionThe G24 memory for incoming short messages is SIM-

SMS4-12 AT Commands Reference Manual January 31, 2007Writing, Saving and Sending Messages (Using AT+CMGW and AT+CMSS)Writing messages into the databa

Chapter 4: Using the Commands January 31, 2007 AT Commands Reference Manual 4-13Sending Messages (Using AT+CMGS)Sends an SM from the G24 to the netwo

Call Control4-14 AT Commands Reference Manual January 31, 2007Call ControlThe following figure is a detailed view of the states the G24 goes through

Chapter 4: Using the Commands January 31, 2007 AT Commands Reference Manual 4-15atd035659260,345,22; //VOICE call with tones sent after connectingOK

Call Control4-16 AT Commands Reference Manual January 31, 2007Dialing the Last Number Exampleatd035658278;OKOKathNO CARRIEROKatdl //Last called numb

Chapter 4: Using the Commands January 31, 2007 AT Commands Reference Manual 4-17Conference Callatd051632601; //Dialing the first member of the confe

Data Call4-18 AT Commands Reference Manual January 31, 2007Data CallSwitching Modes (Data Mode/Command Mode)atd054565190 //Calling the remote modemO

Chapter 4: Using the Commands January 31, 2007 AT Commands Reference Manual 4-19GPRSWhen using the GPRS, it is recommended to implement a "keep

GPRS4-20 AT Commands Reference Manual January 31, 2007Using the ATD* Command SetRequest GPRS service 'D':ATD*99***(CID)#The CID (Context ID

Chapter 4: Using the Commands January 31, 2007 AT Commands Reference Manual 4-21Changing the Character SetExampleWhen an SMS messages with the follow

Fax1-14 AT Commands Reference Manual January 31, 2007FaxOverviewA Service Class 1 facsimile G24 provides a basic level of services necessary to suppo

Sleep Mode4-22 AT Commands Reference Manual January 31, 2007Sleep ModeNote: The notation of TXD and RXD are from the perspective of the terminal unle

Chapter 4: Using the Commands January 31, 2007 AT Commands Reference Manual 4-23TCP/IPTCP Data Transfer ExampleAT+MIPCALL=1,"orange","

TCP/IP4-24 AT Commands Reference Manual January 31, 2007// send a data from terminal to G24 via RS232 communication port:GPRS is the new packet-orien

Chapter 4: Using the Commands January 31, 2007 AT Commands Reference Manual 4-25+MIPOPEN: 1,1AT+MIPOPEN=2,1111,"172.17.238.44",1111,0OK+MIP

TCP/IP4-26 AT Commands Reference Manual January 31, 2007+MIPSEND=1,A344343ABC343438980BC...AB4//Terminal disregards the Xoff request of G24 and keeps

Chapter 4: Using the Commands January 31, 2007 AT Commands Reference Manual 4-27AudioScenarios for Setting Up Handset Mode or Handsfree ModeHandset M

Audio4-28 AT Commands Reference Manual January 31, 2007

January 31, 2007 AT Commands Reference Manual 5-1Chapter 5: ToolsTools OverviewThis chapter describes the PC Driver and PC Loader tools provided by th

PC Driver5-2 AT Commands Reference Manual January 31, 2007Using WinFAX To configure the modem in WinFAX, follow the procedure below:1. Run WinFAX.2.

January 31, 2007 AT Commands Reference Manual A-1Appendix A: Reference TablesThis appendix contains the following sections:• AT Commands Alphabetical

Chapter 1: Product Features January 31, 2007 AT Commands Reference Manual 1-15Character SetsThe following includes the references to various tables t

AT Commands Alphabetical SummaryA-2 AT Commands Reference Manual January 31, 2007&GThis command is supported for backward compatibility only, and

Appendix A: Reference Tables January 31, 2007 AT Commands Reference Manual A-3\GThis command sets the use of the software control.Page 3-233\JThis com

AT Commands Alphabetical SummaryA-4 AT Commands Reference Manual January 31, 2007+CCFCThis command enables control of the call-forwarding supplementa

Appendix A: Reference Tables January 31, 2007 AT Commands Reference Manual A-5+CGEQREQ This command allows the TE to specify a EDGE Quality of Service

AT Commands Alphabetical SummaryA-6 AT Commands Reference Manual January 31, 2007+CIMIThis command requests the International Mobile Subscriber Ident

Appendix A: Reference Tables January 31, 2007 AT Commands Reference Manual A-7+CMER This command enables an external accessory to receive key press in

AT Commands Alphabetical SummaryA-8 AT Commands Reference Manual January 31, 2007+COLP This command refers to the GSM supplementary service COLP, Con

Appendix A: Reference Tables January 31, 2007 AT Commands Reference Manual A-9+CPUCThis command sets the parameters of the Advice of Charge-related pr

AT Commands Alphabetical SummaryA-10 AT Commands Reference Manual January 31, 2007+CSMSThis command handles the selection of the SMS service type.Pag

Appendix A: Reference Tables January 31, 2007 AT Commands Reference Manual A-11+FITThis command is supported for backward compatibility only, and has

Character Sets1-16 AT Commands Reference Manual January 31, 2007Unlike some legacy encoding, UTF-8 is easy to parse. So-called lead and trail bytes a

AT Commands Alphabetical SummaryA-12 AT Commands Reference Manual January 31, 2007+ICFThis command determines the local serial port start/stop (async

Appendix A: Reference Tables January 31, 2007 AT Commands Reference Manual A-13+MCSTThis command displays the current state of the call processing, an

AT Commands Alphabetical SummaryA-14 AT Commands Reference Manual January 31, 2007+MIPCLOSEThis command causes the G24 module to free the socket accu

Appendix A: Reference Tables January 31, 2007 AT Commands Reference Manual A-15+MIPSETSThis command causes the G24 to set a watermark in the accumulat

AT Commands Alphabetical SummaryA-16 AT Commands Reference Manual January 31, 2007+MPINGThis command will allow verifying IP connectivity to another

Appendix A: Reference Tables January 31, 2007 AT Commands Reference Manual A-17+TASWThis command controls the antenna switch mechanism.Page 3-174+TCLC

AT Commands Alphabetical SummaryA-18 AT Commands Reference Manual January 31, 2007EThis command defines whether the G24 echoes the characters receive

Appendix A: Reference Tables January 31, 2007 AT Commands Reference Manual A-19Character Set Table CS1: (GSM -> UCS-2)The following table shows the

Character Set Table CS1: (GSM -> UCS-2)A-20 AT Commands Reference Manual January 31, 20070x060x00F9 ì0x070x00EC ò0x080x00F2 Ç0x090x00C7 LF0x0A0x00

Appendix A: Reference Tables January 31, 2007 AT Commands Reference Manual A-210x270x0027 (0x280x0028 )0x290x0029 *0x2A0x002A +0x2B0x002B ,0x2C0x002C

Chapter 1: Product Features January 31, 2007 AT Commands Reference Manual 1-17AT Commands SummaryThe following list contains a summary of all the G24

Character Set Table CS1: (GSM -> UCS-2)A-22 AT Commands Reference Manual January 31, 20070x480x0048 I0x490x0049 J0x4A0x004A K0x4B0x004B L0x4C0x004

Appendix A: Reference Tables January 31, 2007 AT Commands Reference Manual A-23Character Set Table CS2: (ASCII <-> UTF-8)The following table sho

Character Set Table CS3: (UCS-2 <-> UTF-8)A-24 AT Commands Reference Manual January 31, 2007Character Set Table CS3: (UCS-2 <-> UTF-8)The

Appendix A: Reference Tables January 31, 2007 AT Commands Reference Manual A-25011 013 00B 00001011 VT (Vertical Tab)012 014 00C 00001100 FF (Form Fee

Character Set Table CS7: (ASCII table)A-26 AT Commands Reference Manual January 31, 2007035 043 023 00100011 # (number sign)036 044 024 00100100 $ (d

Appendix A: Reference Tables January 31, 2007 AT Commands Reference Manual A-27067 103 043 01000011 C068 104 044 01000100 D069 105 045 01000101 E070 1

Character Set Table CS7: (ASCII table)A-28 AT Commands Reference Manual January 31, 2007099 143 063 01100011 c100 144 064 01100100 d101 145 065 01100

January 31, 2007 AT Commands Reference Manual B-1Appendix B: MUXThis appendix contains the following sections:• PREMUX State, below• Mux-Init State,

MUX StateB-2 AT Commands Reference Manual January 31, 2007MUX StateEntry to state:• When the G24 receives the SABM0 frame.Exit from state: • When th

Appendix B: MUX January 31, 2007 AT Commands Reference Manual B-3MUX UART Port Speed Auto baud rate detection is disabled in the MUX. To set the UART

January 31, 2007 AT Commands Reference Manual iManual Scope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

AT Commands Summary1-18 AT Commands Reference Manual January 31, 2007H This command hangs up, or terminates a particular call. Page 3-17A This comman

Software Procedures Related to RS232 HW LinesB-4 AT Commands Reference Manual January 31, 2007MUX ModesThe following table describes the differences

Appendix B: MUX January 31, 2007 AT Commands Reference Manual B-5Advance Mode Frame UnpackingThe receiver (referring to the receiver of a frame) exami

Software Procedures Related to RS232 HW LinesB-6 AT Commands Reference Manual January 31, 2007UIH FramesUnnumbered information (UIH) frames contain o

Appendix B: MUX January 31, 2007 AT Commands Reference Manual B-7When a change is made by the G24 to the status of any of the first group of signals i

Software Procedures Related to RS232 HW LinesB-8 AT Commands Reference Manual January 31, 2007The following figure illustrates a MUX user packet, whi

Appendix B: MUX January 31, 2007 AT Commands Reference Manual B-9Open ServiceThe API Open Service MIP and MUI procedures are as follows:• MIP: Use API

Software Procedures Related to RS232 HW LinesB-10 AT Commands Reference Manual January 31, 2007MUX Service TestIncludes MSC, FC, and so on (all to co

January 31, 2007 AT Commands Reference Manual Acr & Abbr-1Acronyms and Abbreviations Abbreviation Full NameA ACCHAT Command Channel - Used for AT

D - HAcr & Abbr-2 AT Commands Reference Manual January 31, 2007D DTMFDual-Tone Multi-FrequencyD DTRData Terminal ReadyE EFElementary FilesE EONSE

I - P Acronyms and Abbreviations January 31, 2007 AT Commands Reference Manual Acr & Abbr-3IICIntegrated CircuitI IDIdentificationI IDLCInformati

Chapter 1: Product Features January 31, 2007 AT Commands Reference Manual 1-19+MVCThis AT command is used to choose and configure the priority order

Q - SAcr & Abbr-4 AT Commands Reference Manual January 31, 2007Q QoSQuality of ServiceQRARecipient AddressQRIRing IndicatorQRTSRequest To SendQRT

T - V Acronyms and Abbreviations January 31, 2007 AT Commands Reference Manual Acr & Abbr-5TTBDTo Be DefinedTTDMATime Division Multiple AccessTTE

January 31, 2007 AT Commands Reference Manual Index-1IndexNumerics8859 Character Set Management, 1-16AAbbreviationsGeneral System, 2-2Aborting Comman

Index A - A Index-2 AT Commands Reference Manual January 31, 2007+CNMI, New Message Indications to Terminal, 3-94+CNUM, Request MSISDN(s), 3-7+COLP,

B - C IndexJanuary 31, 2007 AT Commands Reference Manual Index-33-239S24, Set Number of Seconds Delay before G24 Enters Sleep Mode, 3-238S94, Sideto

Index D - K Index-4 AT Commands Reference Manual January 31, 2007DDataFlush from Buffers, 3-315HDLC Frame, 3-339Push into Protocol Stack, 3-314Recei

L - O IndexJanuary 31, 2007 AT Commands Reference Manual Index-5Keypad Control, 3-262LLast CommandRepeat, 3-213Last NumberDial, 3-16LineIdentificati

Index P - S Index-6 AT Commands Reference Manual January 31, 2007PParamater Read Command SyntaxCommand Mode Types, 2-7Paramater Set Command SyntaxCo

T - W IndexJanuary 31, 2007 AT Commands Reference Manual Index-7TTCP/IP, 1-3, 3-305Features and Benefits, 1-7Overview, 1-3Technical Description, 1-7

AT Commands Summary1-20 AT Commands Reference Manual January 31, 2007+CPBW This command stores a new entry in the phone book, or deletes an existing

@6889192V28@6889192V28-EMOTOROLA and the Stylized M Logo are registered in the US Patent & Trademark Office. All other product or service names ar

Chapter 1: Product Features January 31, 2007 AT Commands Reference Manual 1-21+CGSMS This command handles the selection of the service or service pre

AT Commands Summary1-22 AT Commands Reference Manual January 31, 2007+CBAND This command is supported for backward compatibility only, and has no eff

Chapter 1: Product Features January 31, 2007 AT Commands Reference Manual 1-23AudioGeneral Audio Setup Commands +CRTT This command plays one cycle of

AT Commands Summary1-24 AT Commands Reference Manual January 31, 2007+EPIN This command is only relevant for phones that use SIM cards. It verifies t

Chapter 1: Product Features January 31, 2007 AT Commands Reference Manual 1-25+MSCTS This command defines the behavior of the CTS line when the G24 i

AT Commands Summary1-26 AT Commands Reference Manual January 31, 2007+CIEV An unsolicited indication regarding various phone indications that is sent

Chapter 1: Product Features January 31, 2007 AT Commands Reference Manual 1-27+MIPSETS This command causes the G24 to set a watermark in the accumula

Table of Contentsii AT Commands Reference Manual January 31, 2007Technical Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

AT Commands Summary1-28 AT Commands Reference Manual January 31, 2007&P This command is supported for backward compatibility only, and has no eff

Chapter 1: Product Features January 31, 2007 AT Commands Reference Manual 1-29Fax Class 1Fax Commands+FCLASS This command places the terminal in part

AT Commands Summary1-30 AT Commands Reference Manual January 31, 2007

January 31, 2007 AT Commands Reference Manual 2-1Chapter 2: Introduction to AT CommandsAT Commands OverviewAT commands are sets of commands used for c

AT Commands Protocol2-2 AT Commands Reference Manual January 31, 2007General System AbbreviationsThe basic system configuration contains a modem and

Chapter 2: Introduction to AT Commands January 31, 2007 AT Commands Reference Manual 2-3AT Commands StructureCommand StructureAn AT command line may

AT Commands Structure2-4 AT Commands Reference Manual January 31, 2007Results Code StructureWhen a command is issued, the G24 responds with a message

Chapter 2: Introduction to AT Commands January 31, 2007 AT Commands Reference Manual 2-5AT Commands Protocol & Structure ConfigurationThe AT comm

Command Token Types2-6 AT Commands Reference Manual January 31, 2007Command Token TypesBasic Syntax Command FormatThe format of Basic Syntax commands

Chapter 2: Introduction to AT Commands January 31, 2007 AT Commands Reference Manual 2-7Command Argument Types<value> consists of either a nume

Table of ContentsJanuary 31, 2007 AT Commands Reference Manual iiiSubscriber Unit Identity . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Values2-8 AT Commands Reference Manual January 31, 2007Values Range of ValuesWhen the action accepts a single numeric sub-parameter, or the parameter

Chapter 2: Introduction to AT Commands January 31, 2007 AT Commands Reference Manual 2-9Core AT CommandsThe G24 responds to a limited commands set wh

Core AT Commands2-10 AT Commands Reference Manual January 31, 2007&Y This command displays the default user profile.Page 3-262? This command disp

Chapter 2: Introduction to AT Commands January 31, 2007 AT Commands Reference Manual 2-11+CLCC This command displays a list of all current G24 calls

Core AT Commands2-12 AT Commands Reference Manual January 31, 2007+GMM This command requests the model identification. Page 3-2+GMR This command requ

Chapter 2: Introduction to AT Commands January 31, 2007 AT Commands Reference Manual 2-13+MIPCONF This command allows to configure TCP stack paramete

Core AT Commands2-14 AT Commands Reference Manual January 31, 2007I This command requests various G24 information items. Page 3-6L This command is s

January 31, 2007 AT Commands Reference Manual 3-1Chapter 3: AT Commands ReferenceModem IDSubscriber Unit IdentityThese commands allow the user to quer

Modem ID3-2 AT Commands Reference Manual January 31, 2007+CGMM, +GMM, +FMM, Request Model ID These commands request the model identification. The G24

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-3+CGMR, +GMR, +FMR, Request Revision These commands request the revi

Table of Contentsiv AT Commands Reference Manual January 31, 2007Supplementary Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Modem ID3-4 AT Commands Reference Manual January 31, 2007The following table shows the +CGSN, +GSN parameters.ExampleAT+CGSN?+CGSN: "00440001380

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-5The following table shows the +CSCS parameter optional values.Examp

Modem ID3-6 AT Commands Reference Manual January 31, 2007+CIMI, Request IMSI This command displays the International Mobile Subscriber Identity numbe

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-7The following table shows the information items that are supported

Modem ID3-8 AT Commands Reference Manual January 31, 2007Read CommandThe following table shows the +CNUM parameters.ExampleAT+CNUM?+CNUM: "David

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-9+CLAC, List of All Available AT CommandsExampleAT+CLAC$%C&C&

Modem ID3-10 AT Commands Reference Manual January 31, 2007LMNOPQSTVXYZ\A\SOKCapability ReportingThis set of commands enables a user to determine G24’

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-11Call ControlManaging a CSD (Data) Call The G24 working modes can b

Call Control3-12 AT Commands Reference Manual January 31, 2007Switching From Data Mode to Command Mode To switch the connection from Data mode to Com

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-13Call Control AT CommandsD, Dial Command This command places a FAX/

Table of ContentsJanuary 31, 2007 AT Commands Reference Manual vNetwork Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Call Control3-14 AT Commands Reference Manual January 31, 2007The following table shows the D parameters.Note: ATDP, ATDT, AT*D, <T>, <P>

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-15The following table shows a detailed description for the D> com

Call Control3-16 AT Commands Reference Manual January 31, 2007atd>1; //Speed dial from phonebookOKOKathNO CARRIEROKatd>1 //Speed dial from phon

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-17Note: When ATDL is issued after a dialed number with comma digit:

Call Control3-18 AT Commands Reference Manual January 31, 2007ExampleRING //Incoming callRING //Incoming callath //Hang-up incoming call NO CARRIEROK

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-19A, Answer Incoming Call This command answers an incoming VOICE/DAT

Call Control3-20 AT Commands Reference Manual January 31, 2007RING/+CRING Indication+CRING: <type>or:RINGThe following table shows the +CRC par

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-21RINGAT+CRC=1 //Enable extended ring formatOK+CRING: REL ASYNC+CRIN

Call Control3-22 AT Commands Reference Manual January 31, 2007The following table shows the +CLIP parameters.ExampleAT+CLIP=?+CLIP: (000,001) //CLI p

Chapter 3: AT Commands Reference January 31, 2007 AT Commands Reference Manual 3-23+CCWA, Call Waiting CommandThis command controls the Call Waiting