Motorola 7545MBWM Guía de usuario Pagina 247
- Pagina / 350
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Accessories 5 - 27
ature range. For maximum performance, it is recommended that the charger be operated at room temperature
— a temperature range between 18°C to 25°C (64°F to 77°F).
The charger can consume up to 6 A at 120 VAC, 3A at
240 VAC. Check to ensure the mains circuit supplying
the charger is adequate for this loading (especially if several chargers are being powered from the same
circuit). After unpacking the unit:
• Visually check the charger for damage.
• Install the IEC power cord and apply power.
All charge indicators flash momentarily at power up to indicate that the charger is ready for operation.
If you choose to wall mount the charger, detailed installation instructions are included in the Om
nii 6-Slot
Battery Charger ST3006 Quick Start Guide (PN 8000204) included with the charger kit. Be sure to locate the
charger in an area where there is no risk of injury to persons walking in the vicinity.
Operator Controls
The gang charger does not have operator controls or a power switch. There is no dedicated indicator light to
show that the charger is powered, but the charge slot LEDs will light up briefly when first applying power.
Charge Indicators
Each battery charge slot is equipped with four LEDs to indicate the charge status of the battery. When the
Omnii batteries are inserted in the charger, the colour and behaviour of the LEDs associated with the charging
bays in use indicate the status of the charge.
Charging Batteries
• Install the battery with the battery contacts facing the charger. Slide the battery between the guide rails
until it lightly latches in place.
The 4-LED bar for the battery bay shows 25% charger per LED.
A flashing green LED shows charging is under
way. The LED directly below the slot in which a battery is inserted lights up immediately. If the battery tempera-
ture is outside 0°C to 40°C (32°F to 1
04°F), the LED flashes yellow until the temperature is acceptable. A fully
discharged battery will normally take 4.5 hours to charge. At full capacity, it turns solid green.
When the battery is fully charged, the charger stops applyin
g power; the battery cannot be overcharged if left in
the charger slot.
IMPORTANT Use IEC-320 C13 power cords approved by Motorola, with the ground pin con-
nected to a proper earth-grounded receptacle. Check with a qualified electrician
if you are uncertain of your receptacle grounding.
Charge LED Behav-
iour
Function
OFF No battery detected.
Solid Green Battery charging complete. Each LED represents 25% battery
c
apacity.
Flashing Green Charge in progress. Each LED represents 25% battery capacity.
Flashing Yellow Battery is not charging due to out-of-temperature conditions.
Solid Red Unable to read battery, charging timeout,
or non Motorola battery.
- HAND-HELD COMPUTER 1
- USER GUIDE 1
- OMNII HAND-HELD COMPUTER 3
- Copyright 4
- Disclaimer 4
- Revision History 5
- TABLE OF CONTENTS 7
- Table of Contents vii 9
- Table of Contents ix 11
- Table of Contents xi 13
- Appendices 15
- ABOUT THIS GUIDE 19
- About This Manual 21
- Text Conventions 22
- About This Guide xxi 23
- Figure 1 24
- Figure 2 24
- Regulatory Labels 25
- Laser Warning Label 26
- SE955 Laser Warning Label 26
- LED Radiation Notice Label 26
- SE4600 Laser Warning Label 26
- CHAPTER 1 BASIC OPERATION 27
- Omnii Features 29
- Side Views of the Omnii XT15 30
- Bottom View 30
- Top View 30
- The Battery 31
- Figure 1-6 32
- Performing a Warm Reset 33
- Performing a Cold Reset 33
- Performing a Clean Start 33
- Boot to BooSt 34
- Performing a Hard Reset 34
- Imager and Scanner Options 35
- Connectivity 35
- Data Transfer 35
- Phone Communication 35
- GETTING TO KNOW YOUR OMNII 2 37
- Battery Safety 41
- Battery Swap Time 41
- Standard Keys 43
- Modifier Keys 44
- Activating Modifier Keys 45
- Locking Modifier Keys 45
- Function Keys and Macro Keys 46
- The Keypad Backlight 48
- Calibrating the Touchscreen 49
- Locking the Touchscreen 49
- Battery Charge Status LED 51
- Operating System Status LED 51
- Radio Status LED 51
- Scanner Status LED 51
- Audio Indicators 52
- Vibrations 52
- Inserting the Cards 52
- Scanners and Imagers 53
- Basic Scanner Operations 54
- Scanning Techniques 54
- Navigating Using the Keyboard 56
- The Today Screen 57
- Customizing the Today Screen 58
- Time, Date and Alarms 59
- Text Messages 60
- Menu softkey 61
- Send softkey 61
- E-mail Notification 62
- • Tap on the Calendar sof 63
- Figure 2-6 64
- Favorites 65
- The Start Button 67
- Creating a New Folder 68
- Renaming a File 68
- Copying a File 68
- Deleting a File 69
- Pop-Up Menus 69
- Programs – Using Applications 70
- Using Microsoft ActiveSync 72
- Caring for the Touchscreen 73
- Cleaning the Omnii 73
- CHAPTER 3 PROGRAMS 75
- Programs 77
- The Onscreen Phone Keypad 78
- Programs 3 - 5 79
- Making a Conference Call 79
- Programming Speed Dial 79
- Speed dial number 80
- Call softkey 80
- Programs 3 - 7 81
- Managing Phone Settings 82
- Programs 3 - 9 83
- Programs 3 - 11 85
- Sending an E-mail 86
- Programs 3 - 13 87
- Info Tab 89
- Browsing Web Sites 89
- Calendar 90
- Using the Camera 91
- Moving Photos to the Omnii 92
- Opening a Photo 92
- Deleting a Photo 92
- Editing a Photo 93
- Creating a Slide Show 93
- Using the Video Recorder 93
- Windows Media 94
- Messenger (Windows Live) 94
- Windows Live 95
- Renaming a Note 97
- Recording Notes 97
- Task Notification 98
- Programs 3 - 25 99
- File Explorer 100
- Synchronization 101
- Using Internet Sharing 102
- Task Manager 103
- Search Phone 103
- Imager and Camera Demo 105
- Office Mobile 105
- Excel Mobile 106
- OneNote Mobile 106
- Programs 3 - 33 107
- Programs 3 - 35 109
- Word Mobile 110
- PowerPoint Mobile 110
- SharePoint Workspace Mobile 111
- Modem Link 112
- Remote Desktop Mobile 112
- Ending a Session 113
- CHAPTER 4 SETTINGS 115
- Settings 4 - 3 117
- Motorola Software Advantage 119
- Microsoft Software 119
- Clocks & Alarms 120
- Settings 4 - 7 121
- Battery Power 123
- Advanced Tab 123
- Battery Details Tab 124
- Battery Health 125
- Sounds Tab 126
- Notifications Tab 127
- Bluetooth 128
- Settings 4 - 15 129
- Settings 4 - 17 131
- Pairing a Device 131
- Servers Tab 132
- Settings 4 - 19 133
- Mode Tab 133
- About Tab 134
- Paired Tab 134
- Settings 4 - 21 135
- Settings 4 - 23 137
- Modem Connection Setup 138
- Settings 4 - 25 139
- Advanced Modem Settings 139
- Domain Enroll 140
- Network Cards 141
- Settings 4 - 29 143
- VPN Connection Setup 143
- Tap here 144
- Settings 4 - 31 145
- Proxy Server Tab 145
- Selecting a Network 146
- Settings 4 - 33 147
- Wi-Fi Config: Status Tab 148
- Wi-Fi Config: Configure Tab 148
- Settings 4 - 35 149
- Authentication Mode 150
- Settings 4 - 37 151
- Verify Server Certificate 152
- Enable OPMK 152
- Settings 4 - 39 153
- Configuring TCP/IP 153
- Settings 4 - 41 155
- Wi-Fi Config: Advanced Tab 155
- Wireless Manager 156
- App Launch Keys 157
- Settings 4 - 45 159
- Program Buttons Tab 159
- Up/Down Control Tab 160
- OneShots 160
- Settings 4 - 47 161
- Macro Keys 161
- Unicode Mapping 162
- Settings 4 - 49 163
- Scancode Remapping 163
- The Phone – Managing Settings 165
- Next, tap on the Phone 166
- Settings hotkey 166
- Phone: Sounds Tab 167
- Phone: Security Tab 167
- Phone: Services Tab 169
- Phone: Network Tab 169
- Phone: Data Tab 170
- Phone: Bands Tab 170
- Phone: Diagnostics Tab 170
- Phone: Hearing Aid Mode Tab 171
- Backlight – Screen and Keypad 172
- Settings 4 - 59 173
- Battery Power Tab 173
- External Power Tab 173
- Certificates 174
- Settings 4 - 61 175
- Contrast 177
- Customer Feedback 177
- Dr. Debug 177
- Utilities 178
- Encryption 179
- Error Reporting 180
- Settings 4 - 67 181
- Settings 4 - 69 183
- Imagers Settings 185
- Manage Triggers 186
- Settings 4 - 73 187
- Managed Programs 188
- Microphone 189
- PartnerUp 190
- Settings 4 - 77 191
- Kiosk Menu 191
- Administrator Password 192
- Shell Settings 192
- Settings 4 - 79 193
- Settings 4 - 81 195
- Startup program 196
- Restrictions 197
- Control Panel Settings 198
- Settings 4 - 85 199
- Import and Export Settings 199
- Regional Settings 201
- Remove Programs 202
- Scanner Settings 203
- Double Click Parameters 204
- Display Parameters 204
- Settings 4 - 91 205
- Translations Tab 206
- Settings 4 - 93 207
- Figure 4-1 208
- Settings 4 - 95 209
- Screen Rotation 210
- System Properties 211
- Total Recall 212
- Settings 4 - 99 213
- Creating a Backup 213
- Creating a Clone 214
- Settings 4 - 101 215
- Managing Profiles 215
- Settings 4 - 103 217
- Deleting a Profile 217
- Enable IPv6 218
- (replacing version 4) 218
- Settings 4 - 105 219
- Advanced Services Settings 219
- Registry Editor 220
- CHAPTER 5 ACCESSORIES 221
- Removing the Trigger Cover 223
- Attaching the Pistol Grip 223
- Figure 5-2 224
- The Hand Strap - Model ST6025 225
- Snap Modules 226
- Accessories 5 - 7 227
- (9 pin, 5VDC, 1A max) 227
- Figure 5-7 228
- Charging the Battery 229
- Operator Controls 230
- Accessories 5 - 11 231
- Figure 5-10 232
- Indicators 233
- Operation 233
- Troubleshooting 234
- Cleaning the ST4004 237
- Accessories 5 - 19 239
- Figure 5-17 240
- Accessories 5 - 21 241
- Figure 5-19 242
- Accessories 5 - 23 243
- Wiring Guidelines 243
- Extreme Wet Environments 244
- Accessories 5 - 25 245
- Installation 246
- Charge Indicators 247
- Charging Batteries 247
- APPENDIX A PORT PINOUTS 249
- Omnii Docking Connector 251
- Snap Modules Connectors 252
- Port Pinouts A - 5 253
- 7 6 5 4 3 2 1 254
- APPENDIX B IMAGERS APPLET 255
- Predefined Presets 257
- Barcode Predefined Presets 257
- Using the Imagers Applet 259
- Selecting a Camera 260
- Setting the Active Preset 260
- Viewing a Preset 260
- Creating a Custom Preset 260
- Modifying a Custom Preset 261
- Removing a Custom Preset 262
- Imagers Applet B - 17 271
- Case Rules 271
- Barcode Symbologies 273
- Imager Barcode Symbologies 274
- Imagers Applet B - 21 275
- Imagers Applet B - 22 276
- APPENDIX C SCANNER SETTINGS 277
- Scanner Options 279
- Restoring Default Settings 280
- Decoded (Internal) Scanners 280
- Scanner Settings C - 5 281
- Decoded (HHP) 283
- Decoded (Intermec ISCP) 283
- Non-Decoded Scanners 285
- SCANNER SPECIFICATIONS 287
- SE955 Decode Zones 289
- SE965 Scanner 290
- SE965 Decode Zones 291
- SE1224HP Decode Zones 292
- SE1524ER Decode Zones 293
- EV15 Imager Decode Zone 294
- EA11 Decoded 2D Imager 295
- EA20X Imager 296
- Power Saving Mode 7mA 297
- Parameter Specification 297
- HHP 5080SR Working Range 298
- SE4500SR Decode Zone 301
- SE4600LR – Long Range Imager 302
- SE4600LR Decode Zones 304
- EOmnii Specifications 305
- Hardware 307
- Regulatory Approvals 309
- Wireless Radios 310
- Omnii Specifications E - 7 311
- 802.11a/b/g/n Radio 313
- VARIANTS 317
- Figure F-1 319
- Hardware Specifications 320
- The Freezer Keyboards 322
- Quick Defrost Application 324
- Settings 325
- Heater Info 325
- Heater System 326
- System Test 327
- NETWORK (WWAN) 329
- Wireless WAN 331
- Navigation Bar Icons 331
- Figure G-1 332
- Disconnecting from a Network 333
- Network Configuration 336
- Hearing Aid 336
- APPENDIX H OMNII XT15NI 337
- NON-INCENDIVE SAFETY 337
- GUIDELINES 337
- Numerics 341
- Index - III 343
- Index - V 345
- Index - VII 347
Relacionado con productos y manuales para Computadoras móviles de mano Motorola 7545MBWM
(282 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.037 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales