Motorola LS6000B-U Guía de usuario Pagina 145
- Pagina / 180
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
LS 6000 Scintillation System User’s Manual
PN 247971-F
c-3
RS232
RS232 Data Output
c
<Length> is one printable ASCII character (Hex 20 through 7E or the decimal equivalents
32-126).
The message length includes all characters in the message except <SOH>, <Length>, <CR>
and <LF>. The maximum number of characters on one line is 96, or 94 after <Length>.
Message Length is obtained by subtracting 20 Hex from the <Length> character. For example,
a message with 5 characters would have <Length>
=
<Sequence Number> numbers each message line serially with ASCII characters starting with
<Space>, and ending with
<Message Type> is one printable ASCII character. It identifies the purpose of the message or
its contents as described by the codes in Figure c.2.
<Data Item>
= <Data ID> <Data Type> <Space> <Data Value>
Data ID, type and value are printable ASCII characters as defined below. Data IDs are three
digit numbers and
are listed in Figure c.5 at the end of this section. There are six Data Types
coded by a single letter as defined in Figure c.3.
One or more data items or no data items can be present in a single message. Multiple data
items are separated by semi-co-lons.
Checksum—The checksum is a printable ASCII character, Hex 20 through 7E (or decimal
equivalents 32-126). It is always the lowest two hexadecimal digits of the sum of the ASCII
values of all the characters in the message except <SOH>, <Checksum>, <CR> and <LF>. The
decimal value of the checksum may be computed from the transmitted ASCII characters as:
(ASCII Character of the first value-20 Hex)*64
+ (ASCII Character of the second value-20
Hex).
Carriage Return (CR) is OD, Hex (or 13 decimal). Line Feed (LF) is OA, Hex (or 10,
decimal). Each line closes with CR, LF.
File Header/End of File (F/Z)—During an RS232 session, the LS will indicate the beginning
and end of groups of data with the File Header, F, and the End of File, Z, messages. The File
Figure c.2 Codes for Message Type.
Message Code Purpose/Contents of the Message
DData
E Error
S Send Initiate (Start of Session)
B Break Transmission (End of Session)
F File Header
Z End of file
File Headers are identical in the Datum ID Table.
- LS 6000 Series 1
- Table of Contents 3
- Introduction 11
- Principles of Operation 12
- Operating the Instrument 12
- Operating Modes 13
- 1.3 Specifications 14
- Precautions and Limitations 15
- Figure 1.1 Standard Vial 15
- Miniature Vials 16
- 1.5 Hazards 17
- Maintenance 18
- Getting Started 19
- 2.2 Power Failure 21
- 2.3 Operating Controls 21
- Operator Control Key pad 22
- Using the Operating Controls 24
- 2.4 Using the Racks 25
- Using the Racks 26
- Setting Up the Racks 27
- 2.5 Preparing the Printer 29
- 2.6 System Setup 30
- Energy Scale 31
- Printer Paging 32
- Allow Interrupt Count 32
- System Setup 33
- Figure 2.9 RS232 Setup Menu 33
- Date/Time 35
- Auto DPM 35
- 2.7 Calibration 36
- Counting Samples 39
- Starting the Automatic Count 40
- Conducting Count Single Rack 41
- 3.4 Auto DPM 46
- 3.5 Multi-Task 47
- Interrupt Count in Multi-Task 48
- Multi-Task 50
- Interrupt Data 51
- Setting Up User Programs 59
- 4.2 Editing A User Program 61
- Editing A User Program 62
- Comments 65
- Counting Time 65
- Liquid or Xtal Scintillator 65
- Isotope 1 65
- Isotope 2 and Isotope 3 66
- Edit Other Parameters 67
- Counting Precision 69
- Background/Blank Subtraction 69
- Lum-Ex Correction 71
- Phase Monitor 72
- Low Level 72
- Low Count Reject 72
- Output Formats 72
- Count Data 75
- Raw Data 75
- Collecting Spectral Data 76
- 4.3 Copy User Program 77
- Copy User Program 78
- 5.2 CPM/Xtal CPM 80
- CPM/Xtal CPM 81
- Results for CPM/Xtal CPM 83
- 5.4 Auto DPM 85
- Setting Up Auto DPM 86
- Loading Samples for Auto DPM 86
- Results for Auto DPM 86
- Setting Up DPM 87
- 5.6 Xtal DPM 89
- Xtal DPM 90
- Setting Up Xtal DPM 91
- Loading Samples for Xtal DPM 92
- 5.7 DPM % of Reference 93
- Setting Up DPM % of Reference 94
- Xtal SL DPM % of Reference 95
- 5.9 Single Photon Monitoring 98
- Data Calculation 100
- Single Photon Monitoring 100
- Isotope/DPM Libraries 103
- Accessing the Isotope Library 104
- Printing the Isotope Library 104
- The Isotope Library 105
- Setup Menu 106
- PN 247971-F 108
- 5 minutes 109
- 6.2 Setting Up A Quench Curve 110
- Setting Up A Quench Curve 112
- Counting the Standards 114
- Editing Quench Curves 120
- Deleting A Quench Curve 124
- Manual Entry of Quench Curves 125
- 7.1 Chemiluminescence 127
- Interpretation of Results 128
- Reducing Single Photon Events 128
- 7.3 Two Phase Samples 129
- Procedures 131
- Analysis of Data 131
- H Counting Efficiency 132
- C Counting Efficiency 132
- Background 133
- Contamination 133
- Instrument Specifications 135
- Temperature Control Accessory 138
- Installation Requirements 139
- Electrical Requirements 140
- 0.5 to 1.0 m in 140
- Environment Requirements 142
- . Note that the output 144
- Datum IDs 146
- CHAPTER 1, PART 31 167
- Region I 170
- Region II 170
- Region III 170
- Region IV 170
Relacionado con productos y manuales para Lectores De Códigos De Barras Motorola LS6000B-U
(6 paginas)
(24 paginas)
(32 paginas)
(2 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.117 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales