Motorola LS6000B-U Guía de usuario Pagina 54
- Pagina / 180
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
LS 6000 Scintillation System User’s Manual
PN 247971-F
3-16
Counting Samples
Multi-Task
3. To print the data, highlight “Print Interrupt Data” and press SELECT. All stored data are
printed. Figure 3.14 shows a typical printout. If data is printed during Automatic Count,
the printer advances to the top of the next page before it prints the Interrupt Data. When
Automatic Count is resumed, the Automatic Count data is put on a new page. The
Access Stored Interrupt Data Menu is displayed.
4. To transmit data to the R5232 port, highlight “Send Interrupt Data to RS232” and press
SELECT. All stored data are transmitted. The Access Stored Interrupt Data Menu is
displayed.
NOTE RS232 cannot be used if the current count is generating RS232 output.
5. To erase data, highlight “Erase Interrupt Data” and press SELECT. The data is erased and
the Multi-Task Menu or Main Menu is displayed.
6. If you initiated Access Interrupt Data from Multi-Task, press PREVIOUS MENU to
return to the Auto Count display.
Editing A User Program in Multi-Task
While Auto Count is in progress, you may edit any of the User Programs under Multi-Task.
Editing is performed as described in Section 4. To avoid confusion in the interpretation of
results, the User Program currently in use may only be edited with respect to length of
processing time per sample.
To edit a User Program under Multi-Task:
1. During Automatic Count, press SELECT to display the Multi-Task Menu shown in
Figure 3.8.
2. From the Multi-Task Menu, highlight “Review and Edit User Programs” and press
SELECT. A menu similar to that shown in Figure 3.5 is displayed.
3. Select the desired User Number. The screen displayed is similar to the one shown in
Figure 3.11.
If the User Program in use during Automatic Count is selected, refer to the instructions
given below, Editing the Current User Program.
4. Edit the program as described in Section 4. When editing is complete, press MAIN
MENU. These new parameters are stored in the User Program until changed again. The
Multi-Task Menu is displayed.
5. Press PREVIOUS MENU to return to the Auto Count display.
- LS 6000 Series 1
- Table of Contents 3
- Introduction 11
- Principles of Operation 12
- Operating the Instrument 12
- Operating Modes 13
- 1.3 Specifications 14
- Precautions and Limitations 15
- Figure 1.1 Standard Vial 15
- Miniature Vials 16
- 1.5 Hazards 17
- Maintenance 18
- Getting Started 19
- 2.2 Power Failure 21
- 2.3 Operating Controls 21
- Operator Control Key pad 22
- Using the Operating Controls 24
- 2.4 Using the Racks 25
- Using the Racks 26
- Setting Up the Racks 27
- 2.5 Preparing the Printer 29
- 2.6 System Setup 30
- Energy Scale 31
- Printer Paging 32
- Allow Interrupt Count 32
- System Setup 33
- Figure 2.9 RS232 Setup Menu 33
- Date/Time 35
- Auto DPM 35
- 2.7 Calibration 36
- Counting Samples 39
- Starting the Automatic Count 40
- Conducting Count Single Rack 41
- 3.4 Auto DPM 46
- 3.5 Multi-Task 47
- Interrupt Count in Multi-Task 48
- Multi-Task 50
- Interrupt Data 51
- Setting Up User Programs 59
- 4.2 Editing A User Program 61
- Editing A User Program 62
- Comments 65
- Counting Time 65
- Liquid or Xtal Scintillator 65
- Isotope 1 65
- Isotope 2 and Isotope 3 66
- Edit Other Parameters 67
- Counting Precision 69
- Background/Blank Subtraction 69
- Lum-Ex Correction 71
- Phase Monitor 72
- Low Level 72
- Low Count Reject 72
- Output Formats 72
- Count Data 75
- Raw Data 75
- Collecting Spectral Data 76
- 4.3 Copy User Program 77
- Copy User Program 78
- 5.2 CPM/Xtal CPM 80
- CPM/Xtal CPM 81
- Results for CPM/Xtal CPM 83
- 5.4 Auto DPM 85
- Setting Up Auto DPM 86
- Loading Samples for Auto DPM 86
- Results for Auto DPM 86
- Setting Up DPM 87
- 5.6 Xtal DPM 89
- Xtal DPM 90
- Setting Up Xtal DPM 91
- Loading Samples for Xtal DPM 92
- 5.7 DPM % of Reference 93
- Setting Up DPM % of Reference 94
- Xtal SL DPM % of Reference 95
- 5.9 Single Photon Monitoring 98
- Data Calculation 100
- Single Photon Monitoring 100
- Isotope/DPM Libraries 103
- Accessing the Isotope Library 104
- Printing the Isotope Library 104
- The Isotope Library 105
- Setup Menu 106
- PN 247971-F 108
- 5 minutes 109
- 6.2 Setting Up A Quench Curve 110
- Setting Up A Quench Curve 112
- Counting the Standards 114
- Editing Quench Curves 120
- Deleting A Quench Curve 124
- Manual Entry of Quench Curves 125
- 7.1 Chemiluminescence 127
- Interpretation of Results 128
- Reducing Single Photon Events 128
- 7.3 Two Phase Samples 129
- Procedures 131
- Analysis of Data 131
- H Counting Efficiency 132
- C Counting Efficiency 132
- Background 133
- Contamination 133
- Instrument Specifications 135
- Temperature Control Accessory 138
- Installation Requirements 139
- Electrical Requirements 140
- 0.5 to 1.0 m in 140
- Environment Requirements 142
- . Note that the output 144
- Datum IDs 146
- CHAPTER 1, PART 31 167
- Region I 170
- Region II 170
- Region III 170
- Region IV 170
Relacionado con productos y manuales para Lectores De Códigos De Barras Motorola LS6000B-U
(6 paginas)
(24 paginas)
(32 paginas)
(2 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.087 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales