Motorola LS6000B-U Guía de usuario Pagina 66
- Pagina / 180
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
LS 6000 Scintillation System User’s Manual
PN 247971-F
4-8
Setting Up User Programs
Editing A User Program
Choose SPM (if installed) if you want to do single photon counting. The User Program is
modified for single photon counting. These parameters are not available: Quench Monitor;
Lum-Ex Correction (if installed); 2 Phase (if installed); and Counting Precision. The Data
Calculation program defaults to the Single Photon Program. Refer to Section 5.9 for more
information on single photon monitoring.
Isotope 2 and Isotope 3
The procedure for setting up Isotope 2 and Isotope 3 is identical to that of Isotope 1 except
the list of choices includes NONE. SPM is not included.
For single label studies, choose NONE for Isotopes 2. The prompt for Isotope 3 is not
displayed when Isotope 2 is set to None.
For dual label studies, choose Isotope 1 as the lower energy isotope and Isotope 2 as the
higher energy isotope. The lower limit for Isotope 2 is set the same as the upper limit for
Isotope 1. Choose Isotope 3 as None.
For triple label studies, set up Isotope 3 as the highest energy isotope. The lower limit for
Isotope 3 is set the same as the upper limit for Isotope 2.
- LS 6000 Series 1
- Table of Contents 3
- Introduction 11
- Principles of Operation 12
- Operating the Instrument 12
- Operating Modes 13
- 1.3 Specifications 14
- Precautions and Limitations 15
- Figure 1.1 Standard Vial 15
- Miniature Vials 16
- 1.5 Hazards 17
- Maintenance 18
- Getting Started 19
- 2.2 Power Failure 21
- 2.3 Operating Controls 21
- Operator Control Key pad 22
- Using the Operating Controls 24
- 2.4 Using the Racks 25
- Using the Racks 26
- Setting Up the Racks 27
- 2.5 Preparing the Printer 29
- 2.6 System Setup 30
- Energy Scale 31
- Printer Paging 32
- Allow Interrupt Count 32
- System Setup 33
- Figure 2.9 RS232 Setup Menu 33
- Date/Time 35
- Auto DPM 35
- 2.7 Calibration 36
- Counting Samples 39
- Starting the Automatic Count 40
- Conducting Count Single Rack 41
- 3.4 Auto DPM 46
- 3.5 Multi-Task 47
- Interrupt Count in Multi-Task 48
- Multi-Task 50
- Interrupt Data 51
- Setting Up User Programs 59
- 4.2 Editing A User Program 61
- Editing A User Program 62
- Comments 65
- Counting Time 65
- Liquid or Xtal Scintillator 65
- Isotope 1 65
- Isotope 2 and Isotope 3 66
- Edit Other Parameters 67
- Counting Precision 69
- Background/Blank Subtraction 69
- Lum-Ex Correction 71
- Phase Monitor 72
- Low Level 72
- Low Count Reject 72
- Output Formats 72
- Count Data 75
- Raw Data 75
- Collecting Spectral Data 76
- 4.3 Copy User Program 77
- Copy User Program 78
- 5.2 CPM/Xtal CPM 80
- CPM/Xtal CPM 81
- Results for CPM/Xtal CPM 83
- 5.4 Auto DPM 85
- Setting Up Auto DPM 86
- Loading Samples for Auto DPM 86
- Results for Auto DPM 86
- Setting Up DPM 87
- 5.6 Xtal DPM 89
- Xtal DPM 90
- Setting Up Xtal DPM 91
- Loading Samples for Xtal DPM 92
- 5.7 DPM % of Reference 93
- Setting Up DPM % of Reference 94
- Xtal SL DPM % of Reference 95
- 5.9 Single Photon Monitoring 98
- Data Calculation 100
- Single Photon Monitoring 100
- Isotope/DPM Libraries 103
- Accessing the Isotope Library 104
- Printing the Isotope Library 104
- The Isotope Library 105
- Setup Menu 106
- PN 247971-F 108
- 5 minutes 109
- 6.2 Setting Up A Quench Curve 110
- Setting Up A Quench Curve 112
- Counting the Standards 114
- Editing Quench Curves 120
- Deleting A Quench Curve 124
- Manual Entry of Quench Curves 125
- 7.1 Chemiluminescence 127
- Interpretation of Results 128
- Reducing Single Photon Events 128
- 7.3 Two Phase Samples 129
- Procedures 131
- Analysis of Data 131
- H Counting Efficiency 132
- C Counting Efficiency 132
- Background 133
- Contamination 133
- Instrument Specifications 135
- Temperature Control Accessory 138
- Installation Requirements 139
- Electrical Requirements 140
- 0.5 to 1.0 m in 140
- Environment Requirements 142
- . Note that the output 144
- Datum IDs 146
- CHAPTER 1, PART 31 167
- Region I 170
- Region II 170
- Region III 170
- Region IV 170
Relacionado con productos y manuales para Lectores De Códigos De Barras Motorola LS6000B-U
(6 paginas)
(24 paginas)
(32 paginas)
(2 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.286 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales